Single and Variable Speed
Jig Saws
INSTRUCTION MANUAL
Catalog Nos. 7552, JS200, JS300
BEFORE RETURNING THIS PRODUCT FOR ANY REASON PLEASE CALL
1-800-54-HOW-TO (544-6986)
IF YOU SHOULD EXPERIENCE A PROBLEM WITH YOUR BLACK & DECKER PURCHASE,
CALL 1-800-54-HOW-TO (1-800-544-6986).
IN MOST CASES, A BLACK & DECKER REPRESENTATIVE
CAN RESOLVE YOUR PROBLEM OVER THE PHONE.
IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL
condition that may affect the tools operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.
•Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool, may become hazardous when used on another tool.
SERVICE
•Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury.
•When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury.
SPECIFIC SAFETY RULES
•Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.
The label on your tool may include the following symbols.
V | volts | A | amperes | |||
Hz | hertz | W | watts | |||
min | minutes | no | alternating current | |||
|
| direct current | no load speed | |||
|
| |||||
| .......................... | Class II Construction |
|
| ........................ | earthing terminal |
|
|
|
|
| ||
|
|
|
|
| ||
| ........................ | safety alert symbol | .../min | revolutions or | ||
|
|
|
|
|
| reciprocations |
|
|
|
|
|
| per minute |
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con- struction activities contains chemicals known to cause cancer, birth defects or other repro- ductive harm. Some examples of these chemicals are:
•lead from
•crystalline silica from bricks and cement and other masonry products, and
•arsenic and chromium from
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.
CAUTION: Wear appropriate hearing protection during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.
ADDITIONAL SAFETY RULES: JIG SAWS
•KEEP HANDS AWAY from cutting area. Never reach underneath the material for any reason.
•KEEP BLADES SHARP. Dull blades may cause the saw to swerve or stall under pressure.
TO THE SUCCESS OF BLACK & DECKER'S QUALITY
IMPROVEMENT PROGRAM.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
INSTRUCTIVO DE OPERACIÓ N, CENTROS DE SERVICIO Y PÓ LIZA
DE GARANTÍA. ADVERTENCIA: LÉ ASE ESTE INSTRUCTIVO ANTES
DE USAR EL PRODUCTO.
CAT. NO. 7552, JS200, JS300 | FORM NO. | PRINTED IN CHINA |
GENERAL SAFETY RULES
WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
•Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
•Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
•Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control.
A
1
BLADE CLAMP
PORTA SEGUETAS
ROLLER SUPPORT
GUIDE
ROULEAU PORTEUR
GUIA DE SOPORTE DE
RODILLO
SCREW
ARRIÈRE
TORNILLO
3
SHOE
PATIN
ZAPATA DUST BLOWER
SOPLADOR DE POLVO
4
OUICK CLAMP™ BLADE CLAMP
LEVER
LEVIER DU
CLAMPmc
PALANCA DEL PORTA SEGUETAS
QUICK CLAMP™
BLADE
LAME
SEGUETA
LOCK ON BUTTON
BOUTON DE VERROUILLAGE
EN MODE DE
FONCTIONNEMENT
BOTON DE ENCENDIDO
PERMANENTE
TRIGGER SWITCH
INTERRUPTEUR À
DÉTENTE
GATILLO
INTERRUPTOR
R
BLADE STORAGE
RANGEMENT DE
LA LAME
COMPARTIMIENTO
PARA SEGUETAS
ELECTRICAL SAFETY
•Double insulated tools are equipped with a polarized plug (one blade is wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. Double insulation 
eliminates the need for the three wire grounded power cord and grounded power supply system.
•Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded.
•Don’t expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
•Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.
•When operating a power tool outside, use an outdoor extension cord marked
PERSONAL SAFETY
•Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
•Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair can be caught in moving parts. Air vents cover moving parts and should be avoided.
•Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents.
•Remove adjusting keys or wrenches before turning the tool on. A wrench or key that is left attached to a rotating part of the tool may result in personal injury.
•Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.
•Use safety equipment. Always wear eye protection. Dust mask,
TOOL USE AND CARE
•Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.
•Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.
•Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired.
•Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventative safety measures reduce the risk of starting the tool accidentally.
•Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.
•Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control.
•Check for misalignment or binding of moving parts, breakage of parts, and any other
5
EXTENSION CORDS
When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord
|
|
| Minimum Gauge for Cord Sets |
| ||
Volts |
|
| Total Length of Cord in Feet | |||
120V |
| |||||
240V |
| |||||
Ampere Rating | American Wire Gage |
| ||||
More |
| Not more |
| |||
Than |
| Than |
|
|
|
|
0 | - | 6 | 18 | 16 | 16 | 14 |
6 | - | 10 | 18 | 16 | 14 | 12 |
10 | - | 12 | 16 | 16 | 14 | 12 |
12 | - | 16 | 14 | 12 | Not Recommended | |
MOTOR
Be sure your power supply agrees with nameplate marking. 120 Volts AC only means your tool will operate on standard 60 Hz household power. Do not operate AC tools on DC. A rating of 120 volts AC/DC means that you tool will operate on standard 60 Hz AC or DC power. This information is printed on the nameplate. Lower voltage will cause loss of power and can result in
ASSEMBLY/ADJUSTMENT SET-UP
INSTALLING BLADES
(7552) MANUAL BLADE CHANGE MODELS ONLY USE THESE BLADE TYPES 
BEFORE INSTALLING BLADES, TURN OFF AND UNPLUG TOOL.
Loosen (do not remove) the two screws "A" in Figure 1. Ensure the blade teeth are facing forward and insert the saw blade shank fully into the blade clamp. Slightly tighten screws alternately to position the blade, then fully tighten screws. To release, turn both screws one turn counterclockwise.