Craftsman 315.21477 manual Tres, Blade GUmDES, General, Lubrication, Screw Bladegudes

Page 21

WARNING:Whenservicing,useonlyidentical

replacementparts.Useofanyotherpartmaycreate

ahazardorcauseproductdamage.

_k WARNING: Always wear safety goggles or safety glasses with side sMelds during power tool operation

or when blowing dust. Hfoperation is dusty, also wear a dust mask.

GENERAL

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.

_ WAF{NJNG: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating

oils, etc. come in contact with plastic parts. Chemi- cals can damage, weaken or destroy plastic which may result in serious personal injury.

Hthas been found that electric tools are subject to accelerated wear and possible premature failure when they are used on fiberglass boats, sports cars, wallboard, spackling compounds, or piaster. The chips and gdndings from these materials are highly abrasive to electric too! parts such as bearings, brushes, commutators, etc. Consequently, it is not recommended that this too! be used for extended work on any fiberglass material, wail- board, spackling compounds, or piaster. During any use on these materials it is extremely important that the tool is cleaned frequently by blowing with an air jet.

[] Keep your band saw clean.

[] Remove sawdust from the inside frequently.

[] Do not allow pitch to accumulate on the saw table, blade guides, or thrust bearings. Clean them with gum and pitch remover.

[] Apply a thin coat of automobile type wax to the saw table's top so the wood slides easily while cutting.

LUBRICATION

All of the beadngs in this tool are lubricated with a suffi- cient amount of high grade lubricant for the life of the unit under normal operating conditions. Therefore, no further lubrication is required.

WARNING: To ensure safety and reliability, all repairs -- with the exception of the externally acces- sible brushes -- should be performed by a qualified service technician at a Sears store to avoid risk of personal injury.

T(RES

Cleaning tires:

[] Pitch and sawdust accumulates on tires and needs to be

removed with a fine wire brush or a piece of wood. Do not use a sharp knife or any kind of solvent.

RepJacing tires:

[] Open front cover and remove saw blade. See section on hstalling and Adjusting the Blade, page !4.

[] Pry the worn tire away from the wheel carefully.

[] Stretch the new tire around the wheel.

[] Replace the saw blade and close the front cover.

BLADE GUmDES

See Figure 20.

Blade guides may become rounded and worn during use.

[] Unplug the band saw.

[] Remove the blade guides and file or grind flat.

[] Replace blade guides when filing or grinding has worn them down and they can no longer be properly secured in place.

UPPER BLADE

GUIDE SUPPORT

THRUST

BEARING

SCREW

L

BLADEGU(DES

BLADE GUIDE

SUPPORT SCREW

BLADE GUARD REMOVED

FOR CLARIFICATIONONLY

Fig. 20

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Save this manual for future reference Customer HeUp LineFull ONE Year Warranty on Craftsman Tool Blade Coasts After Turn OFF Read ALL mNSTRUCTmONSAllowthemotorto Come UP to Full Speed Before Making a CUT, be Sure ALL ADJUST- Ments are SecureSymbol NA!Vi EDESJGNATION/EXPLANATION SERVmCE Symbol Signal MeaningExtension Cords Speed and WiringElectrical Connection GroundingCrosscut Anti=KickbackPawlsradialarm and table sawsSwitch Switchkey Oubtexhaubt Port Andadapter Locklever Scale Indicator Bladetension KnobProduct SPECmFmCATmONS ViewwindowSee Figure Know Your Band SAWHexkey AdjustablewrenchLeadingto possibleseriouspersonalinjury To do socouldresultin possibleseriouspersonal injuryAligning Bolt Lock Handle Mounting the SAW TableCLAMPmNG Band SAW to Workbench MOUNTmNG Band SAW 30 WorkbenchMNSTALUNG and ADJUSTmNG the Blade ADJUSTmNG Blade GUmDE AssemblySee Figures 9 Lever Setscrews SAW WingAdjustng Blade Tenson See Figures 10Tenbion Squaring the SAW Table to the Blade BladeonSee Figures 14 Blade GuideThrustbearing Bladeguide Assembly ReAdjust BladeGuidesCUTTmNG Procedures Basic Operation of the Band SAWScroll CUTTmNG RELmEF CutsRemoving Jammed Material AVOmDmNG mNJURYSwitch KEY Locking the SwitchBlade GUmDES TresGeneral LubricationMOTOR/ELECTRmCAL BrushesDrive Belt Problem Cause See AdjustmentsSOLUTmON Page Figure a Craftsman Band SAW- Model noAngle Scale Labe Bolt M6 x 16 ram Craftsman Band SAW- Model no BS90101600 Figure O Craftsman Band SAW Model noSee Back page for Parts Ordering Instructions Craftsman Band SAW- Model noBand SAW- Model no CraftsmanDomicilio, y para Sears Parts & Repair CenterLE- Foyer Mc SU-HOGAR

315.21477 specifications

The Craftsman 315.21477 is a versatile and highly sought-after tool known for its robust performance and user-friendly design. This tool is part of the Craftsman brand, which has built a reputation for quality and reliability over the years. The 315.21477 model is particularly favored among DIY enthusiasts and professionals alike for its innovative features and technologies.

One of the main features of the Craftsman 315.21477 is its powerful motor, which provides ample torque and speed for a variety of applications, from home repairs to intricate crafting projects. The tool is equipped with a variable speed control system, allowing users to adjust the speed settings according to the task at hand. This flexibility makes it ideal for tasks that require precision, such as sanding, drilling, and cutting.

The Craftsman 315.21477 is built with user comfort in mind. It features an ergonomic design that reduces hand fatigue, ensuring users can work for extended periods without discomfort. The rubberized grip provides a secure hold, giving users increased control and stability while using the tool. Additionally, the lightweight construction makes it easy to maneuver, making it perfect for both indoor and outdoor use.

In terms of versatility, the Craftsman 315.21477 boasts a range of attachments and accessories that allow it to perform multiple functions. From changing attachments to switching between various tasks, the tool can easily adapt to meet the needs of different projects. This multi-functionality reduces the need for multiple tools, saving both space and money.

Safety is a key consideration in the design of the Craftsman 315.21477. The tool comes equipped with safety features such as a paddle switch for easy shutdown and a built-in overload protection system, which helps prevent damage to the motor in case of excessive strain.

In summary, the Craftsman 315.21477 stands out in the market due to its powerful motor, variable speed control, ergonomic design, versatility, and enhanced safety features. It is a reliable choice for anyone looking to tackle a wide range of tasks with ease and efficiency. Whether you are a seasoned professional or a casual DIYer, the Craftsman 315.21477 offers the performance and reliability needed to get the job done right.
Top Page Image Contents