Craftsman 315.24234, 315.21234 manual Parts List Figure B

Page 37

37

CRAFTSMAN COMPOUND MITER SAW – MODEL NUMBER 315.212340 & 315.242340

The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your Compound Miter Saw or when ordering repair parts.

PARTS LIST - FIGURE B

Key	Part	Description	Qty.
No.	Number	Description	Qty.
1	511414000	Spacer	1
2	A50060030040	Ball Bearing (6003Z/RS)	1
3	511334000	* Screw (M5 x 6mm)	2
4	A63020000350	O-Ring (S-35)	1
5	511335000	Bearing Cover	1
6	511336000	Gasket	1
7	511337000	Gear Shaft	1
8	A45204040180	Key (4 X 4 X 18L)	1
9	588029007	Lock Ring	1
10	608309000	Master Gear	1
11	A46000150008	C-Ring (S-15)	2
12	A50060000027	Ball Bearing (6000ZZ) **STD315511	1
13	588027005	Compression Spring	1
14	588026106	Arbor Lock Pin	1
15	A47000040006	E-Ring (E4)	1
16	511313000	Warning Label, Motor	1
17	511353000	Warning Label	1
18	A18003100206	* Depth Adjusting Bolt (M10 x 20mm)	1
19	A30003010007	Hex Nut (M10) **STD844010	1
20	A18003050054	* Screw (M5 x 5mm)	2
21	A95001050060	* Screw (M5 x 6mm)	2
22	588005100	Brush Cap	2
23	588006100	Carbon Brush	2
24	588007300	Brush Holder	2
25	A18003050086	* Screw (M5 x 8mm)	1
26	511339000	Arm	1
27	A510001040120	* Screw (M4 x 12mm)	3
28	588021203	Rubber Stopper	1
29	A10003040207	* Screw (M4 x 20mm)	1
30	A70003060250	* Screw (M6 x 25mm)	2
31	A10003050400	* Screw (M5 x 40mm)	4
32	511311000	Carry Handle	1
33	511352000	Twist Handle Warning Label	1
34	511340000	Twist Handle	1
35	S51100700	Arbor Assembly (Includes Key Nos. 2 thru 12)	1

*Standard Hardware Item – May Be Purchased Locally

**Available from Div 98 – Source 980.0

Image 37

Contents Operators Manual Introduction WarrantyRead ALL Instructions General Safety RulesInspect Extension Cords Periodically and replace if damaged Specific Safety RulesSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceElectrical Cord Length Wire Size A.W.GDouble Insulation Electrical ConnectionGlossary of Terms Product Specifications FeaturesMiter Scale AMP Motor Know Your Compound Miter SAWCarrying Handle Spindle Lock ButtonLaser Guide Rotating HandlePositive Stops on Miter Table Bevel Lock KnobCombination Wrench Tools Needed10 mm,14 mm Combination Square Framing Square Phillips ScrewdriverLoose Parts List Unpacking AssemblyMounting Holes Dust Guide Dust BAGLoosen Exhaust Port Dust Guide MiterSee Figures 12 Table ExtensionsWork Clamp To Install BladeSee Figures 15 Phillips Screw Work Clamp Base Lower Blade Guard BracketBlade Tighten Phillips Screw Blade Bolt Cover Lower Blade GuardBolt Spindle Lock ButtonAligning the Laser Guide Line Mounting the Laser GuideBlade Laser Guide Inner Blade Washer Blade WrenchSee Figures 20 Squaring the Miter Table to the FenceSee Figures 24 Squaring the SAW Blade to the FenceBase Framing Square Mm SocketSee Figures 28 Squaring the Blade to the Miter TableFence Combination Square Lock NutsApplications OperationCutting with the Compound Miter SAW Crosscutting Fence Combination Square BladeTo Miter CUT Indicator Point Scale MountingTo Bevel CUT See Figures 33To Make a Compound CUT To Compound Miter CUTBevel CUT Compound Miter CUTLong Workpiece Workpiece Supports Support Long WorkpiecesCutting Compound Miters COMPOUND-ANGLE Settings for Popular StructuresPitch Number of Sides Laying Molding Flat on the Miter Table Cutting Crown MoldingMiter Table Crown Molding Flat on Miter Table Clamping Wide Workpieces Cutting Warped MaterialSee Figures 39 WrongPivot Adjustments Travel Pivot Adjustment AdjustmentsBevel Pivot Adjustment Depth StopDepth Stop Adjustments MaintenanceBrush Replacement GeneralChanging the Batteries Figure a Craftsman Compound Miter SAW Model Number 315.212340Key Part Description Qty Number Parts List Figure aSee Note Parts List Figure B Figure C Key Part Parts List Figure CDescription Qty Number Page Key Part Number Description Qty Get it fixed, at your home or ours