Craftsman 351.21833 Installation, Install Miter Gauge, Install Push Stick, Install RIP Fence

Page 13

Set Screws

Latches

Figure 36 - Latches Lock and Unlock Blade Guard and Pawls to Riving knife

INSTALL MITER GAUGE

Refer to Figure 37.

¥The miter gauge comes preassembled. Unpack the miter gauge and clean thoroughly. Insert into storage slots on right side of cabinet.

Figure 37

INSTALL PUSH STICK

Refer to Figure 38.

¥Insert the push stick into brackets on left side of base.

Figure 38

INSTALL RIP FENCE

Refer to Figure 39.

¥Position rip fence assembly at end of saw. Be certain lock- ing lever is in UP unlocked position.

¥Place rip fence assembly onto rails, positioning clamp over rear rail and then placing rip fence onto front guide rail.

¥Rip fence should now ride freely on rip fence rails. Once rip fence is completely installed, it should be parallel with the miter gauge and perpendicular to the table. If not, refer to ÒRip Fence AdjustmentÓ in the Operation section of this manual.

Figure 39

INSTALLATION

GROUNDING INSTRUCTIONS

WARNING: Improper connection of equipment grounding con- ductor can result in the risk of electrical shock. Equipment should be grounded while in use to protect operator from electrical shock.

¥Check with a qualified electrician if grounding instructions are not understood or if in doubt as to whether the tool is properly grounded.

¥This tool is equipped with an approved 3-conductor cord rated at 300V and a 3-prong grounding type plug (see Figure 40) for your protection against shock hazards.

¥Grounding plug should be plugged directly into a properly installed and grounded 3-prong grounding-type receptacle, as shown (Figure 40).

Properly Grounded Outlet

Grounding Prong

3-Prong Plug

Figure 40 - 3-Prong Receptacle

¥Do not remove or alter grounding prong in any manner. In the event of a malfunction or breakdown, grounding pro- vides a path of least resistance for electrical shock.

WARNING: Do not permit fingers to touch the terminals of plug when installing or removing from outlet.

¥Plug must be plugged into matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not modify plug provided. If it will not fit in outlet, have proper outlet installed by a qualified electrician.

13

Image 13
Contents Operator’s Manual Warranty Table of ContentsSafety Rules Location Stability of SAWKickbacks Protection EYES, HANDS, FACE, BODY, EarsKnow Your Cutting Tools USE only Accessories Designed for SAWUnpacking Think SafetySAW Installation AssemblyInstall Handwheels Remove Packing MaterialAttach Caster Sets to Base Assemble Caster SetsAttach Base to Cabinet Attach Cord Wrap HooksAttach RIP Fence Brackets Blade Guard and Push Stick Storage BracketsAttach Extension Tables Install BladeCheck Table Alignment Aligning Miter Slots to Blade Rail AssemblyPosition and Adjust Riving Knife Attach Switch AssemblyRiving Knife to Blade Adjustment Install Table InsertAttach Blade Guard and ANTI-KICKBACK Pawls Install Miter Gauge InstallationInstall Push Stick Install RIP FenceOperation Blade Tilt Adjustment Blade Height AdjustmentStarting and Stopping the SAW Table Insert Adjustment Stop AdjustmentMiter Gauge Adjustment Setting Clamping Pressure RIP Fence AdjustmentSetting Fence Perpendicular and Parallel Cursor AdjustmentTypes of CUTS/OPERATIONS RIP Fence OperationCrosscutting Miter CuttingCleaning MaintenanceCutting Oversized Workpieces Dust CollectingLubrication ServiceChanging the SAW Blade Date Maintenance Performed Replacement Parts Required Service RecordSymptom Possible Causes Corrective Action TroubleshootingTroubleshooting Model QTY KEY DescriptionReplacement Parts Illustration for Cabinet Recommended Accessory Replacement Parts List for CabinetKEY Description QTY Replacement Parts Illustration for Rails Replacement Parts List for Rails Replacement Parts Illustration for Base KEY NO. Part no Description Replacement Parts List for BaseReplacement Parts Illustration for Blade Drive Replacement Parts List for Blade Drive Replacement Parts Illustration for Blade Guard Replacement Parts List for Blade Guard Get it fixed, at your home or ours