Zenoah SGCZ2600DW, SGCZ2600DL HOW to MIX Fuel, Fueling the Unit, For Your Engine LIFE, Avoid

Page 9

7. Fuel

FUEL

WARNING

Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refuel- ing the unit. Select outdoor bare ground for fuel- ing and move at least 3 m (10 ft) away from the fueling point before starting the engine.

The Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If Zenoah oil is not available, use an anti-oxidant added quality oil expressly labeled for air-cooled 2-cycle engine use (JASO FC GRADE OIL or ISO EGC GRADE).

Do not use BIA or TCW (2-stroke water-cooling type) mixed oil.

RECOMMENDED MIXING RATIO GASOLINE 50 : OIL 1

(WHEN USING ZENOAH GENUINE OIL)

Exhaust emission are controlled by the fundamen- tal engine parameters and components (eq., carburation, ignition timing and port timing) with- out addition of any major hardware or the intro- duction of an inert material during combustion.

These engines are certified to operate on unleaded gasoline.

Make sure to use gasoline with a minimum octane number of 89RON (USA/Canada: 87AL).

If you use a gasoline of a lower octane value than prescribed, there is a danger that the engine tem- perature may rise and an engine problem such as piston seizing may consequently occur.

Unleaded gasoline is recommended to reduce the contamination of the air for the sake of your health and the environment.

Poor quality gasolines or oils may damage sealing rings, fuel lines or fuel tank of the engine.

HOW TO MIX FUEL

IMPORTANT

Pay attention to agitation.

1.Measure out the quantities of gasoline and oil to be mixed.

2.Put some of the gasoline into a clean, approved fuel container.

SGCZ2600DL/SGCZ2600DW

3.

Pour in all of the oil and agitate well.

 

4.

Pour in the rest of gasoline and agitate again for at

 

 

least one minute. As some oils may be difficult to

 

 

agitate depending on oil ingredients, sufficient agi-

 

 

tation is necessary for the engine to last long. Be

G

 

careful that, if the agitation is insufficient, there is an

 

increased danger of early piston seizing due to ab-

B

 

normally lean mixture.

 

5.

Put a clear indication on the outside of the container

 

 

to avoid mixing up with gasoline or other containers.

 

6.

Indicate the contents on outside of container for easy

 

 

identification.

 

FUELING THE UNIT

1.Untwist and remove the fuel cap. Rest the cap on a dustless place.

2.Put fuel into the fuel tank to 80% of the full capacity.

3.Fasten the fuel cap securely and wipe up any fuel spillage around the unit.

WARNING

1.Select bare ground for fueling.

2.Move at least 3 meters (10 feet ) away from the fueling point before starting the engine.

3.Stop the engine before refueling the unit. At that time, be sure to sufficiently agitate the mixed gaso- line in the container.

FOR YOUR ENGINE LIFE, AVOID:

1.FUEL WITH NO OIL (RAW GASOLINE) – It will cause severe damage to the internal engine parts very quickly.

2.GASOHOL – It can cause deterioration of rubber and/ or plastic parts and disruption of engine lubrication.

3.OIL FOR 4-CYCLE ENGINE USE – It can cause spark plug fouling, exhaust port blocking, or piston ring sticking.

4.Mixed fuels which have been left unused for a pe- riod of one month or more may clog the carburetor and result in the engine failing to operate properly.

5.In the case of storing the product for a long period of time, clean the fuel tank after rendering it empty. Next, activate the engine and empty the carburetor of the composite fuel.

6.In the case of scrapping the used mixed oil container, scrap it only at an authorized repository site.

NOTE

As for details of quality assurance, read the description in the section Limited Warranty carefully. Moreover, nor- mal wear and change in product with no functional influ- ence are not covered by the warranty. Also, be careful that, if the usage in the instruction manual is not observed as to the mixed gasoline, etc. described therein, it may not be covered by the warranty.

GB-9

Image 9
Contents SGCZ2600DL SGCZ2600DW E13*97/68SH2G3*2002/88*0094*03 Wear head, eye and ear protectionParts location ContentsSymbolson the machine SpecificationModel SGCZ2600DL SGCZ2600DWWorking Condition For safe operationWorking Circumstance Working PlanUsing the Product Before Starting EngineStarting the Engine If Someone Comes MaintenanceHandling Fuel TransportationSet up Fuel HOW to MIX FuelFuel Fueling the UnitAdjusting Idling Speed Adjusting Throttle CableOperation Starting EngineHOW to USE HOW to WearHarness Balance the UnitRoad edge Near fences Around stones Cutting WorkRecommended Applications Among treesMaintenance Maintenance ChartBlade AIR Filter Replacement Plug is a NGK CMR7AFuel Filter Spark PlugStorage Procedures to be Performed After EV- ERY 100 Hours of USEDisposal Intake AIR Cooling VentTroubleshooting guide Limited warrantyCheck Probable Causes Action

SGCZ2600DW, SGCZ2600DL specifications

The Zenoah SGCZ2600DL and SGCZ2600DW are commercial-grade grass trimmers that have made a significant impact in the landscaping industry due to their reliability, performance, and advanced technology. These models are engineered to deliver exceptional cutting power and efficiency, making them ideal for both professional landscapers and garden enthusiasts.

One of the standout features of the SGCZ2600DL and SGCZ2600DW is their powerful 26cc two-stroke engine, which provides a robust performance without compromising on weight. The engine is designed to deliver high torque along with a consistent power output, allowing users to tackle tough jobs with ease. Additionally, both models are equipped with a reliable ignition system that ensures easy starting and minimal maintenance.

The ergonomic design of these trimmers enhances user comfort during prolonged usage. With a lightweight frame and well-balanced construction, users can maneuver the tool effortlessly, reducing fatigue during extended trimming sessions. The adjustable handles further enhance user control, allowing for precise cutting at various angles.

In terms of cutting technology, the SGCZ2600DL and SGCZ2600DW feature a dual-line bump feed head. This system allows for quick and efficient line advancement, enabling users to reload the trimmer line with minimal downtime. The dual-line configuration also provides a wider cutting path, thus increasing productivity and reducing the time needed for clearing larger areas of grass and weeds.

Both models are designed for durability, featuring high-quality materials that can withstand challenging working conditions. The reinforced housing and components ensure that the trimmers remain operational even in demanding environments. Furthermore, the SGCZ2600DL and SGCZ2600DW utilize advanced anti-vibration technology, which reduces the amount of vibration transferred to the user's hands, further improving comfort and usability.

Another noteworthy aspect is the fuel efficiency of these machines. They are crafted to optimize fuel consumption while minimizing emissions, which aligns with modern environmental standards. This not only benefits the user financially but also contributes to a greener planet.

Overall, the Zenoah SGCZ2600DL and SGCZ2600DW trimmers stand out in the market for their combination of power, efficiency, and user-friendly design. Suitable for various landscaping tasks, these tools exemplify the quality and innovation that Zenoah is known for, making them a valuable addition to any gardening toolkit.