DismantiingSc Assembly Instructions

3)AteaysyseStS~owectsiii&Si^acttypesocket

2)Use extra (Seep aocfceES in piSCft 03 exiewfoti bars where

lÃˆs$ibte

3)&onotusewss^Kf.wornwaaticeasocteis.

4)MofetBwwrenchsotiieSOCK(Mfitssquara-iyon!hefastener.Hofsfthe wrench S r w ! ~bat nottoo tightty,ptesskig forward sSigitB^

Disconnect toot iwmairsupply.

Take out oil plug(2) swd ttcaxi ttw (ttt wntaioed in the fron eeoct of

the toot into a suitable corrtainer. Grip motor housing (1) in a vise fitted with soft jaws and unscrew4 screws with washers (33) and pull off housing(46) as fittedand ramova O-ring (45).Oil seat (47) may be hooked out of arri awil bushing (44) pressed out of housing (46). Remove anvil Spacer (41). PuH off the hammer mechanism completely awl pull it apart to separate anvil (40) or

(49). spring (39).2 hammer pins (37),hammer cam (381,cam ball (36).cam ball pilot (35)and hammer cage (34). Socket ring (43) and 0 ' r i i '(4S)~ may bpriedoff awil(40) but do not try to remove assembly iterris (SO) (coif) anvil (49).

Remove 4 screws with washers (33) ana carefullypulloff end cap

(28)and gas-fet(29)completewith air regulator assembly. Remove C-ring (30)and regulatorswefMAy may be pullet) through end cap (28)being careful not to tose spring (31) and steel ball (32)

Remove O-ring(27) ffotti air regulator reverse (26). Note in particularthe orientationof the parts to each otherfor reassembly. Unscrew how adaptor {&) and take off exhaust dettector <8).Pull out rear end plate (24) frith bait beating (25). TOW(22). cylinder {20). guide pin(23)and G row blades<Â£?from motorhousing(1).

Tap out fromendpiate(19) completewithO+nog(13),oil sea){I?) and bat! tearing ($6)from Iwysing{f). Bat1 bearing <2S) may be lapped out ofrear andplate (24) and oil $MI<1?)arrf&&Ibeating

(IS)retrieved!mton! pMe{?9}.fiemove2$(yews(iS)atÃ§icare fuBywSsiosx!fpttSwttrigawass~hemhOTisung{I).The

Uiggaassail(naybasepwatediWparts<*, .iriggerpaifKLstop

mwi-US),Â ¥ { h w btisttitjga O-fifOS(11)an3E-r&j(3). Nste

theSoeaBsn arri onentaaw of aii pass (w fsas?w*3y.

Reassembly

Cteanaii parts and waroKia iwwear arwi cracte. eit;. and repiacs as necessary.Loot; inpartkoiarfa: wear antf cursoo 0-tiwjsand

seais awl w a r on row bia<tes.Lot*for waat andcrackson piam of th@ hammer mscfiacAsm paqicotarty in Ihs area ofthe square

drive an arwils'(40) or (49). RspIace all parts a r e necessary

with manufacturer or authorial distribmor supplied parts. Make

sure that.the faces of end plates (19) and {24}That abut cylinder

(20)are itat and free ifom surfacedetectsanti bum. Ifnecessary. lap faces with a vary twin.grade of abrasive paper. Ugh* coat aH

partswith a suitablepneumatict w l lybricalinflOil anC!asseffif&lein

the reverseorder. On completing assembly, emure that all pans

are locked tight, the anvil will rotate, and the trigger r e vatve and air regulate mechanism operate freeiy. Reiftow oil plug (2) and pour is38fl. oz.{iZcc) of a standard SASM)gradti oit. Do not (werfia as this wit! wstjK in a iedu&r> in p e t t o r a n e e . Pour in awm.5 mi oi a good quafay fubfiaaiq 04 <owprefefSSiy contaiaiRg a mi ittht&ttor)istotfte (rose a&#tw (9) with the

aitgswdepressed.Confleciloaswtabfe&staspiyawlruniheto<a

foi a few secortds ta a8aw I h e oiS to cirwhls and reset fof

operaikiS.ReferK;s e e m Operating.

As; CQft~ymc&M	I		3.5 cte> (25ach)
lifaMmumT o w Reverse	1	2 i O tt. !bs. (285 ?0)
WortangToque Reverse	1 S 1 8 5 f(. W .(08-251Nm}
MaximumTorque Forward	I	W i t i b s . pi51 Mm)
		-,----
WorkingTorque Forward		50-160ft.IteS.(68-217Nm)
~ iInletr ?l'arsatf	I	\ "	W ~ S M P T
OverallLength	1		6.25- (159 mm)

at 90 PSIW6.2bar

Declaration of Conformity

Sioux Tools, Inc.

117 Levi Drive, Murphy, NC 28906, U.S.A.

declare under our sole responsibSty that the product

Model 5038Bl5039B ImpactWrenches, Serial Number

to which this declaration relates is in conformitywith the following standard($) of other normative docurnent(s)

EN792 (Draft), EN292 Parts 1 & 2, IS0 8662 Parts 1 & 7, Pneurop PN8NTC1

foliowingthe provisions of 891392EEC as amended by 91/368/EEC& 93144EEC Directives

@t A -

G a .Seebeck (President)

Primed in Japan

Page No 3

3)&onotusewss^Kf.wornwaaticeasocteis.