RedMax BM40S manual Set up

Page 5

4. For safe operation

Make sure the spray hose loops freely without kinking or squeezing.

4.After using sprayers and other equipment, CLEAN UP! Dispose of debris in trash receptacles.

MAINTENANCE

1. In order to maintain your product in proper working order, perform the maintenance and checking

operations described in the manual at regular intervals.

2. Examine the sprayer at intervals for loose fasteners and rusted or damaged parts.

Use special care for chemical leakage.

3 Clean and rinse tank and spraying assembly after each use to prevent crystallizing, which would later cause clogging and chemical damage to the unit.

4.All service except for those described in this manual should be performed by competent service personnel.

5.When replacing the any other part, or any lubricant, always be sure to use only RedMax products or products which have been certified by RedMax for use with the RedMax product.

6.In the event that any part must be replaced or any maintenance or repair work not described in this manual must be performed, please contact a representative from the store nearest RedMax authorized servicing dealer for assistance.

7.Do not use any accessory or attachment other than those bearing the RedMax mark and recommended for the unit.

8.Under no circumstances should you ever take apart the product or alter it in any way. Doing so might result in the product becoming damaged during operation or the product becoming unable to operate properly.

TRANSPORTATION

Clean and rinse tank and spraying assembly after each use to prevent crystallizing, which would later cause clogging and chemical damage to the unit.

Drain the content from the tank before transporting or storing the sprayer.

Secure the unit carefully to prevent movement when it is transported.

A unit that receives a strong shock during transport and unloading may malfunction.

STORAGE

Clean and rinse tank and spraying assembly after each use to prevent crystallizing, which would later cause clogging and chemical damage to the unit.

Do not store sprayer under pressure, or with spray solution in tank.

When storing the sprayer, choose a space indoors free from moisture and out of the reach of children.

DISPOSAL

When disposing your machine, or chemical, be sure to allow your local regulations.

5. Set up

NOTE

Hose clamps are not completely tight. Please tighten hose clamps prior to using.

Hose clamps are left loose to extend life of gaskets and fittings.

WARNING

Oil cap gasket before using and lubricate weekly so the gasket will seal properly and prevent chemical leaks.

Oil check valve and maintain breather hole clear of debris. Your failure to oil may can cause the tank to collapse and crack due to vacuum created by pump lubricate with "3 and 1" oil.

IMPORTANT

Make sure to insert the locking pin for the pump handle in its (only) CORRECT POSITION.

The pin limits the pump stroke for optimum performance without see page. Observe Fig. 1 exactly. (Fig. 2 and 3 spell trouble.)

For best results and to maintain a good seal, re-grease piston sleeve periodically with vaseline or similar light lubricants.

HOW TO ASSEMBLE

1.Attach spray wand to spray gun and tighten firmly.

2.Take pump handle RMKIT 7 and insert into the tube on the pump lever RMKIT 5 ("T" shape lever on sprayer), you will notice holes drilled through both sides of both the pump handle and the pump lever. Align these holes, take the "R" pin provided and place through the holes. This affixes the handle in place and is ready for use.

For storage reverse process and then place "R" pin through the pump lever RMKIT to keep from losing "R" pin.

3.Instructions for installing shoulder strap plastic buckle: First put the sprayer on a hard flat surface, take the white plastic buckle and while holding the sprayer up slightly, place buckle under the tubular metal frame. Slowly push down forcing the frame into the buckle. Repeat the same procedure for other side.

5

Image 5
Contents BM40S Contents Safety FirstBefore Using SpecificationsParts location For safe operationWorking Plan Using the ProductSet up HOW to Prepare Your Unit for USE HOW to Adjust the NozzlePre-operation OperationSpryaer Maintenance Table MaintenanceStorage DisposalPage Parts list Parts List BM40S Description Qty Limited Warranty