Earlex V0053 instruction manual Spray Pack Must be, Assembled Before Filling

				5) Fitting of Straps to Spray Pack:
				i. Fit the strap hooks into the round holes at the top
				of the Spray Pack.
				ii. Feed the strap through the vertical slots at the
				bottom of the Spray Pack, loop around and feed
Spray Pack				back through the strap buckle.
				Spraying
PLEASE READ MAIN INSTRUCTION MANUAL				IT IS RECOMMENDED THAT THE UNIT IS TESTED WITH
				WATER PRIOR TO EACH USE
BEFORE USE				1. Remove Spray Pack Lid (2) and pour in required
Important Information				spray material and thinners.
				2. Ensure the spray material and thinners do not
This Spray Pack is only to be used with the following				exceed the max fill line on the Spray Pack.
				3. Fit the Spray Pack Lid, ensuring that Seal (3) is
Earlex HVLP units, Spray Station 2900, 3500 and 3900.				present. Make sure the lid is tightened securely.
Using with another HVLP unit may affect the Spray				4. Connect the hose that is supplied with your Earlex
				Spray Station into the back of the Spray Gun.
Pack’s performance. This does not affect your				5. Put the Spray Pack on your back and tighten straps
statutory rights.				(WARNING: Spray Pack weighs approximately 5kg
This 4 litre Spray Pack is designed to fit your back. It				when full).
				6. Ensure the Spray Pack is secure on your back and
allows for large painting jobs to be completed without
				the straps are tightened. The Spray Pack should sit
the need to re-fill, saving you a substantial amount of
				in your upper back area for optimum working
time. There are jobs where the use of the 1 litre
				spray height.
container is more appropriate:
				7. Turn on the Spray Station unit, hold the Spray Gun
				lower than Spray Pack until the liquid reaches the
Which Container	4litre Spray Pack		1litre
				Spray Gun, then you are ready to start spraying.
should I use?		Container		Overalls, goggles, mask and gloves should be worn
For ceiling	Not recommended		Yes	whilst using spray equipment.
For wall or floor	Yes		Yes	Cleaning Instructions
With water based	Yes		Yes
product				The Spray Pack must be thoroughly cleaned
With solvent based	Not recommended as		Yes	immediately after use. If the paint dries inside the
product	a lot of thinners will be			Spray Pack, cleaning will become much more
	required for the clean			difficult and may render the Spray Pack inoperable.
	up
Undercoats	Not recommended		Yes	This is not covered by the guarantee.
Smooth masonry	Not recommended		Yes	• Remove the Spray Pack Lid (2).
paints
				• Pour any leftover paint into a container so that it
				can be used in the future. Wipe the Spray Pack to
NB: As per the use of the 1 litre container, low				remove as much as possible.
temperatures can make paint thicker and we therefore				• Pour a quantity of thinners or water into the
recommend spraying at a minimum of 15°C.				container, shake the Spray Pack lightly, reassemble
				the Spray Pack, then spray this liquid through the
THE SPRAY PACK MUST BE				Spray Gun. Repeat this process until the thinner
				being sprayed is coming through with no traces of
ASSEMBLED BEFORE FILLING				paint.
Set Up for HV2900, 3500 or 3900 (Fig.1)				• Clean any traces of paint off the outside of the
				Spray Gun.
1) Using scissors or a sharp knife, split the Twin Tube (5)				Troubleshooting
at both ends.
				PROBLEM		WHAT IS THE SOLUTION?
2) Put the Hose Clips (6) at each end of the striped
				Spray material		1. Check Air feed Hose and Spray Pack
tube (Fig.2).
3) Take the Spray Gun and remove the Paint				does not reach		Container lid are sealed and fully tightened.
Container and Pick-Up Tube.				Spray Gun		2. Check if Spray Gun Fluid Tip is blocked
4) Connect the striped tube to the bottom of the				when trigger is		and Fluid Needle is free to move.
Spray Pack (Fig.2, 1a) and the other end to the
				activated		3. Check the dilution of your paint and if
paint pick up (Fig.2, 1b) of the Spray Gun, and
						necessary dilute more.
connect the unstriped tube to the top of the Spray
Pack (Fig.2, 2a) and the other end to the air outlet						4. Level of spray material in container is
on the Spray Gun (Fig.2, 2b).						too low, refill.
HINT: Running the end of the tubes under warm				Design Registrations;
water will ease the fitting onto the Spray Gun and
				GB 3022948	FR 06/5462 US D562,544 CA 118106
Spray Pack.
						V0053 07/09

Earlex Ltd, Tel: +44 (0)1483 454666, Email: enquiries@earlex.co.uk, Website: www.earlex.com