307-293 | Graco 231-005, Series A, 215-433 Series G specification

WARNING

HIGH PRESSURE SPRAY CAN CAUSE SERIOUS INJURY. For professional use only. Observe

all warnings. Read and understand all instruction manuals before operating equipment.

FLUID INJECTION HAZARD

General Safety

This equipment generates very high fluid pressure. Spray from the gun, leaks or ruptured components can inject fluid through your skin and into your body and cause extremely serious bodily injury, including the need for amputation. Fluid injected or splashed into the eyes or on the skin can cause serious damage.

NEVER point the spray gun at anyone or at any part of the body. NEVER put hand or fingers over the spray tip. NEVER try to "blow back" paint; this is NOT an air spray system.

ALWAYS have the tip guard on the spray gu n when spraying.

ALWAYS follow the Pressure Relief Procedure, below, before cleaning or removing the spray tip or servicing any system equipment.

NEVER try to stop or deflect leaks with your hand or body.

Be sure equipment safety devices are operating properly before each use.

Medical Alert-Airless Spray Wound

If any fluid appears to penetrate your skin, get EMERGENCY MEDICAL CARE AT ONCE. DO NOT TREAT AS A SIMPLE CUT. Tell the doctor exactly what fluid was injected.

Note to Phys/cilln: Injection in the skin is a traumatic injury. It is important to treat the injury surgically 8S soon as possible. Do not delay treatment to research toxicity. Tox- icity is a concern with some exotic coatings injected directly into the blood stream. Consultation with a plastic surgeon or reconstructive hand surgeon may be advisable.

Spray Gun Safety Devices

Be sure all gun safety devices are operating properly before each use. Do not remove or modify any part of the gun; this can cause a malfunction and result in serious bodily injury.

Safety Latch

Whenever you stop spraying, even for a moment, always set the gun safety latch in the closed or "safe" position, making the gun inoperative. Failure to set the safety latch can result in accidental triggering of the gun.

Diffuser

The gun diffuser breaks up spray and reduces the risk of fluid injection when the tip is not installed. Check diffuser operation regularly. Follow the Pressure Relief Procedure, below, then remove the spray tip. Aim the gun into a metal pail, holding the gun firmly to the pail. Using the lowest possible pressure, trigger the gun. If the fluid emitted is not diffused in- to an irregular stream, replace the diffuser immediately.

Tip Guard

ALWAYS have the tip guard in place on the spray gun while spraying. The tip guard alerts you to the fluid injection hazard and helps reduce, but does not prevent, accidentally placing your fingers or any part of your body close to the spray tip.

Trigger Guard

Always have the trigger guard in place on the gun when spray- ing to reduce the risk of accidentally triggering the gun if it is dropped or bumped.

Spray Tip Safety

Use extreme caution when cleaning or changing spray tips. If the spray tip clogs while spraying, engage the gun safety latch immediately. ALWAYS follow the Pressure Relief Pro- cedure and then remove the spray tip to clean it.

NEVER wipe off build-up around the spray tip until pressure is fully relieved and the gun safety latch is engaged.

Pressure Relief Procedure

To reduce the risk of serious bodily injury, including fluid injection, splashing in the eyes or on the skin, or injury from moving parts, always follow this procedure whenever you shut off the sprayer, when checking or servicing any part of the spray system, when installing, cleaning or changing spray tips, and whenever you stop spraying. (1) Engage the gun safety latch. (2) Open the bypass valve. (3) Depress the engine stop button. (4) Close the fuel shutoff valve. (5) Disengage the gun safety latch and hold a metal part of the gun firmly to the side of-a grounded metal pail, and trigger the gun to relieve pressure. (6) Engage the gun safe- ty latch. (7) Open the drain valve, having a container ready to catch the drainage. (8) Leave the drain valve open until you are ready to spray again.

If you suspect that the spray tip or hose is completely clogged, or that pressure has not been fully relieved after following the steps above, VERY SLOWLY loosen the tip guard retaining nut or hose end coupling and relieve pressure gradually, then loosen

completely. Now clear the tip or hose.

2 307-293

231-005, 215-433 Series G, Series A specifications

Graco is a renowned manufacturer known for its high-quality spray equipment and pumps, catering to both professionals and DIY enthusiasts. Their diverse lineup includes advanced models such as Series A, Series C, Model 237069, Model 289310, and Model 238620, each uniquely engineered to meet various painting and coating applications.

The Graco Series A is an outstanding choice for smaller projects. Its lightweight design and portability make it ideal for residential touch-ups, woodworking, and other small-scale applications. This series boasts a simple setup with an easy-to-use spray gun that enables users to achieve a smooth, even finish. Equipped with Graco’s ProConnect technology, Series A allows for quick pump replacement without any tools, ensuring minimal downtime during projects.

The Graco Series C offers enhanced performance and greater versatility for larger applications. This series is designed for professional contractors and serious DIYers, featuring robust construction and advanced technology. With a higher flow rate and pressure capabilities, Series C can handle more demanding projects such as residential and commercial buildings. Additionally, it incorporates SmartControl technology, electronically controlling pressure to provide consistent spray patterns regardless of the fluid being used.

Model 237069 is another exceptional option known for its compact design and efficiency. This electric airless sprayer is perfect for various interior and exterior applications, standing out due to its ease of operation. It features a reversible spray tip, allowing users to quickly clear clogs, and the adjustable pressure settings provide flexibility for different surface textures. Model 237069 is engineered for durability, making it a reliable choice for frequent use.

Model 289310 is engineered for professionals who prioritize speed and precision. This heavy-duty sprayer is equipped with an advanced hydraulic system, which ensures a consistent flow of material. Its larger hopper capacity minimizes the need for frequent refills, allowing users to complete extensive projects faster. Furthermore, the model includes an ergonomic design that reduces fatigue, empowering operators to work longer with comfort.

Lastly, Model 238620 exemplifies Graco’s commitment to innovation in airless technology. This model features an integrated digital display that offers real-time feedback and monitoring, enhancing overall user experience. With its streamlined pump design and advanced filter system, Model 238620 is capable of handling a wide range of coatings, from thin stains to thick latex paints.

In conclusion, Graco's Series A, Series C, Model 237069, Model 289310, and Model 238620 represent the brand’s dedication to quality, performance, and user-friendliness. These models cater to various project sizes and requirements, making them valuable assets for both amateurs and seasoned professionals in the painting industry.