Grizzly G5353 instruction manual Troubleshooting, Symptom Possible Cause Solution

Page 15

Troubleshooting

Symptom

Possible Cause

Solution

 

 

 

 

 

 

 

 

 

Fluttering or spitting

1. Dry or worn fluid tip seat per-

1.

Tighten fluid tip or replace

spray.

 

mits air to seep into fluid pas-

 

seat with new one.

 

 

 

 

 

 

 

sage.

 

 

 

 

 

 

 

 

2.

Material level too low.

2.

Add material.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

Fluid tip or filter obstructed.

3.

Clean.

 

 

 

 

 

 

4.

Dry needle packing.

4.

Lubricate needle.

 

 

 

 

 

 

 

 

 

Uneven top

 

or

bot-

1. Atomizing cap holes are

1.

Clear holes.

tom

pattern.

 

 

 

 

obstructed.

 

 

 

 

 

 

 

 

2.

Build-up on top or bottom of

2.

Clean.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

fluid tip.

 

 

 

 

 

 

 

 

3.

Build-up on atomizing cap is

3.

Clean.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

on needle seat.

 

 

 

 

 

 

 

 

 

 

 

Right or left arc

1. Left or right side horn holes

1.

Clear holes.

pattern.

 

are plugged.

 

 

 

 

 

 

 

 

2.

Build-up on left or right side of

2.

Clean.

 

 

 

 

 

 

 

fluid tip.

 

 

 

 

 

 

 

 

3.

Build-up of material inside

3. Clean.

 

 

 

 

 

 

 

atomizing cap.

 

 

 

 

 

 

 

 

 

 

 

Heavy deposit of

1. The material flow exceeds the

1.

Lower fluid flow.

material in center.

 

atomizing cap capacity.

 

 

 

 

 

 

 

 

2.

Inlet air pressure is too low.

2.

Increase inlet air pressure.

 

 

 

 

 

 

3.

Material is too thick.

3.

Thin material.

 

 

 

 

 

 

 

 

 

Narrow center pat-

1. Volume control turned in too

1.

Increase volume.

tern.

 

far.

 

 

 

 

 

 

 

 

2.

Inlet air pressure too high.

2.

Reduce inlet air pressure.

 

 

 

 

 

 

3.

Fluid pressure is too low.

3.

Increase fluid pressure.

 

 

 

 

 

 

4.

Material is too thin.

4.

Adjust material.

 

 

 

 

 

 

 

 

 

No spray output.

1. No pressure at gun.

1.

Check air supply.

 

 

 

 

 

 

2.

Fluid passages dirty.

2.

Clean gun, remove any

 

 

 

 

 

 

 

 

 

obstructions.

 

 

 

 

 

 

3.

Fluid control closed.

3.

Open.

 

 

 

 

 

 

4.

Out of paint.

4.

Refill.

 

 

 

 

 

 

5.

Material too thick.

5.

Thin to manufacturer's rec-

 

 

 

 

 

 

 

 

 

ommendations.

 

 

 

 

 

 

 

 

 

 

Model G5353 Spray Gun

-15-

Image 15
Contents Spray GUN Model G5353 Mation about proper operation of the equipment SafetySafety Instructions For Pneumatic Tools Before Operating This EquipmentSafety Instructions For Pneumatic Tools Operating PRESSURE. do Additional Safety Instructions for Spray GunsForeword Contact Information Introduction6MM G5353Liter SiphonCup SET UPInventoryAssembly Model G5353 Inventory FigureControls ControlsOperations SprayingTo use your spray gun Spray technique YesNo Fan adjustment Model G5353 Spray Gun Atomizing Cap Fan AdjustmentsH3174-Air Blow Gun with 2 Tips AccessoriesG6261-Campbell Hausfeld Water Filter H7274-Campbell Hausfeld Pressure RegulatorDisconnect the gun from the com- pressed air MaintenanceCleaning To clean your spray gunGeneral lubrication points Model G5353 Spray Gun LubricationSymptom Possible Cause Solution TroubleshootingSymptom Possible Cause Solution REF Description Parts Breakdown G5353Warranty and Returns Warranty Card BOX BELLINGHAM, WA Name Street CityStateZip