Specific Safety Rules

14 . 4 VOLT DRILL

INSTRUCTION MANUAL

Catalog Number FS1402D

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-544-6986

IF YOU SHOULD EXPERIENCE A PROBLEM

WITH YOUR BLACK & DECKER PRODUCT,

CALL 1-800-544-6986

BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG No.,

TYPE No., AND DATE CODE. IN MOST CASES, A BLACK & DECKER REPRESENTATIVE CAN

RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT,

GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.

SAVE THIS MANUAL FOR

FUTURE REFERENCE.

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y

PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE

INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

GENERAL SAFETY RULES - FOR ALL BATTERY OPERATED TOOLS

WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS.

Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

Work Area

•Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

•Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

•Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control.

Electrical Safety

•Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edge are less likely to bind and are easier to control.with sharp.

•Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.

•Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may create a risk of injury when used on another tool.

Service

•Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury.

•When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury.

•Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.

•When working on a ladder or on scaffolding be sure to lay the tool down on its side when not in use. Some tools with large battery packs will stand upright but may be easily knocked over.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•lead from lead-based paints,

•crystalline silica from bricks and cement and other masonry products, and

•arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.

The label on your tool may include the following symbols.

V		volts	A		amperes
Hz		hertz	W		watts
min		minutes	no		alternating current
		direct current			no load speed
		direct current			no load speed
	..........................	Class II Construction		........................	earthing terminal


	........................	safety alert symbol	.../min		revolutions or
			reciprocations per minute

Battery Cap Information

Battery storage and carrying caps are provided for use whenever the battery is out of the tool or charger. Remove cap before placing battery in charger or tool.

WARNING! Do not store or carry battery so that metal objects can contact exposed battery terminals. For example, do not place battery in aprons, pockets, tool boxes, product kit boxes, drawers, etc. with loose nails, screws, keys, etc. without battery cap. Without cap in place, battery could short circuit causing fire or burns or damage to battery.

Battery Cap

Capuchon du bloc-pile

Protector de la batería

•Do not abuse the cord. Never use the cord to carry the tool. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords may create a fire.

•A battery operated tool with integral batteries or a separate battery pack must be recharged only with the specified charger for the battery. A charger that may be suitable for one type of battery may create a risk of fire when used with another battery.

•Use battery operated tool only with specifically designated battery pack. Use of any other batteries may create a risk of fire.

Personal Safety

•Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.

•Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair can be caught in moving parts. Air vents cover moving parts and should be avoided.

•Avoid accidental starting. Be sure switch is in the locked or off position before inserting battery pack. Carrying tools with your finger on the switch or inserting the battery pack into a tool with the switch on invites accidents.

•Remove adjusting keys or wrenches before turning the tool on. A wrench or key that is left attached to a rotating part of the tool may result in personal injury.

•Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.

•Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

Tool Use and Care

•Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.

•Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.

•Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with the switch is dangerous and must be repaired.

•Disconnect battery pack from tool or place the switch in the locked or off position before making any adjustments, changing accessories, or storing the tool. Such preventative safety measures reduce the risk of starting the tool accidentally.

•Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.

•When battery pack is not in use, keep it away from other metal objects like: paper clips, coins, keys, nails, screws or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause sparks, burns, or a fire.

3
3				Depress for forward (other side)
				Enfoncer pour la marche avant
Depress for reverse (this side)				Enfoncer pour la marche avant
Depress for reverse (this side)				(autre côté)
Enfoncer pour la marche arrière				(autre côté)
Enfoncer pour la marche arrière				Oprima para marcha adelante
(ce côté)				Oprima para marcha adelante
(ce côté)				(otro lado)
Oprima para reversa (este lado)				(otro lado)
Oprima para reversa (este lado)

Trigger Switch

Interrupteur à gâchette

Conmutador tipo gatillo

Gear Shifter

Bouton à deux vitesses d’engrenage Palanca de cambio

Torque Adjust Collar

Collier de réglage de couple

Collar de ajuste de par torsor

FS1402D specifications

The Black & Decker FS1402D is a versatile and compact electric sander designed for both amateur DIY enthusiasts and professional craftsmen. This power tool excels in delivering a smooth finish, making it a go-to choice for various sanding tasks. One of its standout features is its innovative design that combines performance with user-friendly functionality.

The FS1402D features a powerful 140-watt motor that provides ample power for tackling different materials, including wood, plastic, and metal. This motor ensures that the sander operates efficiently, making it suitable for a range of applications from furniture refinishing to detail work. Its lightweight and compact design contribute to easy maneuverability, allowing users to sand in tight spaces or overhead applications without straining.

One of the key technologies integrated into the FS1402D is its unique dust collection system. The sander comes equipped with a built-in dust bag that captures debris effectively, helping to keep your workspace clean and improving visibility while you work. This feature not only enhances the sanding experience but also contributes to a healthier work environment by minimizing airborne dust.

The Black & Decker FS1402D is also designed for ease of use, featuring an ergonomic grip that reduces fatigue during extended use. This thoughtful design allows for better control and precision, ensuring that users achieve the desired results without compromising comfort. Additionally, the sander is compatible with a range of sanding sheets, giving users the flexibility to choose the right grit for their specific project.

Another impressive characteristic of the FS1402D is its speed control feature, allowing users to adjust the sanding speed according to the material and the task at hand. This versatility ensures optimal sanding results, whether it's removing paint, smoothing rough edges, or fine-tuning surfaces.

In summary, the Black & Decker FS1402D combines power, portability, and user-friendly features, making it an essential tool for both casual and professional users. Its robust motor, effective dust collection system, ergonomic design, and adjustable speed settings come together to create a powerful yet manageable sander that delivers outstanding performance. Whether you are tackling a large project or working on intricate details, the FS1402D is engineered to help you achieve a flawless finish every time.