Epson DW130 Motor Brushes, Spade Handle Assembly Fig, Side Handle Fig, Switch Fig

130 5/17/02 3:26 PM Page 6 (Black plate)

ORK. Use clamps or a vise to hold work. It’s safer ur hand and it frees both hands to operate tool. RREACH. Keep proper footing and balance at all

OOLS WITH CARE. Keep tools sharp and clean for er performance. Follow instructions for lubricating accessories. Inspect tool cords periodically and if ve repaired by authorized service facility. Inspect rds periodically and replace if damaged. Keep lean, and free from oil and grease.

T OR LOCK OFF TOOLS when not in use, before when changing accessories, such as blades, bits,

JUSTING KEYS AND WRENCHES. Form habit of

eethat keys and adjusting wrenches are removed re turning it on.

NTENTIONAL STARTING. Don’t carry tool with ch. Be sure switch is off when plugging in. CORDS. Make sure your extension cord is in good hen using an extension cord, be sure to use one h to carry the current your product will draw. An rd will cause a drop in line voltage resulting in loss overheating. The following table shows the correct epending on cord length and nameplate ampere oubt, use the next heavier gage. The smaller the

the heavier the cord.

Minimum Gage for Cord Sets

Total Length of Cord in Feet

	0-25	26-50	51-100	101-150
Rating	0-50	51-100	101-200	201-300
		AWG
Not more
Than	18	16	16	14
6
10	18	16	14	12
12	16	16	14	12
16	14	12	Not Recommended

2

•OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked.

•STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool when you are tired.

•CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual. Have defective switches replaced by authorized service center. Do not use tool if switch does not turn it on and off.

•CAUTION: When drilling or driving into walls, floors or wherever live electrical wires may be encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool only by insulated grasping surfaces to prevent electric shock if you drill or drive into a live wire.

SAVE THESE INSTRUCTIONS

Motor Brushes

Be sure tool is unplugged before inspecting brushes. To inspect brushes, unscrew the plastic brush inspection caps (located in the sides of the motor housing) and withdraw the brush assemblies from the tool.

Keep brushes clean and sliding freely in their guides. Carbon brushes have varying symbols stamped into them, and if the brush is worn down to a point where the symbol is not visible, they must be replaced. New brush assemblies are available at Service Centers; see TOOLS, ELECTRIC in the Yellow Pages.

NOTE: This tool is designed to automatically turn itself off when the brushes are worn out.

Spade Handle Assembly: (Fig. 1)

This spade handle can be attached either horizontally or vertically. Place the handle into the locating boss on the back of the drill and assemble with holding knob.

Side Handle (Fig. 1)

The side handle can be placed in either side of the drill or the top of the drill according to operator preference and available working clearance. The spade handle can be temporarily removed if working clearance at rear of tool is limited. Always replace spade handle when possible.

CAUTION: Always use the side handle and switch handle. This is a high-torque drill. Always hold it firmly with both hands when operating.

FIG. 1

Switch: (Fig. 2)

Pressing the TOP part of the switch runs the tool in a re Pressing the BOTTOM part of the switch runs the to direction. Always let the motor stop completely be direction.

To lock trigger in “FORWARD” position, depress LOW and push up lock button “B”. Then, while holding lock b gently release trigger. To release locking mechanism, fully, then release it.

NOTE: Locking mechanism will not function if upper p depressed (reverse operation).

The locking feature is for use when the drill is mounted in otherwise firmly held...NOT BY HAND.

Do not lock the switch “ON” when drilling by hand instantly release the trigger switch if the bit binds in the h Be sure to release the switch locking button before dis plug from the power supply. Failure to do so will cause immediately the next time it is plugged in. Damage result.

REVERSE	R
FORWARD	F

TRIGGER SWITCH

LOCK BUTTON “B”

3