Disassembly/Assembly Instructions .7 Hp Drill

Disassembly/Assembly Instructions - .7 Hp Drill

Important: Manufacturer’s warranty is void if tool is disassembled before warranty expires.

Please refer to parts breakdown for part identification.

Motor Disassembly:

1.Disconnect tool from power source. Remove chuck from spindle.

2.Secure motor housing using padded vise with motor spindle facing upwards.

3.Using an adjustable pin wrench, remove 13432 Spindle Cover.

4.Remove 04014 Set Screw from housing.

5.Pull 53181 Spindle and planetary carrier assembly from housing.

6.Press planetary carrier assembly from rear 02552 Bearing. Remove ring gear and gears from 53180 Planetary Carrier.

7.Secure planetary carrier in vise and remove 53181 Spindle. Press carrier from front 02552 Bearing.

8.Grab onto rotor/pinion and pull motor assembly from motor housing.

9.Press rotor/pinion from 13440 Rear Bearing Plate. Press 02649 Rear Bearing from rear bearing plate.

10.Remove 01028 Cylinder and 01185 Rotor Blades from rotor.

11.Press rotor pinion assembly through 01007 Front Bearing and 53183 Front Bearing Plate.

Motor Disassembly Complete.

Housing Disassembly:

1.Position housing in padded vise with air inlet facing up.

2.Remove air fitting by securing 94523 Inlet Adapter with a wrench and twist air fitting from inlet adapter.

Important: 94523 Inlet Adapter must be secured before attempting to remove air fitting to avoid damaging valve body housing.

3.Remove 94523 Inlet Adapter.

4.Remove 95711 Retaining Ring from inlet adapter and separate 94521 Muffler Base from 94522 Muffler Cap. Remove 94528 Felt Muffler.

5.Remove air control ring from housing.

6.Using a 2.5 mm drift pin, tap 01017 Pin from housing and remove throttle lever assembly.

7.Remove 13427 Plug. Pull 13437 Speed Regulator from housing and remove 01024 O-Rings, 07145 Spring, 13439 Ball, and 13435 Valve Stem.

Disassembly Complete.

Motor Assembly:

Important: Be sure parts are clean and in good repair before assembling. Follow all grease, oil, and torque specifications.

1.Place rotor/pinion in padded vise with threaded spindle facing upwards.

2.Slip 01010 Spacer onto rotor/pinion.

3.Place a .002" shim into 53183 Front Bearing Plate as an initial spacing and slip 01007 Bearing into plate. Note: 01121 Shim Pack contains .001" and .002" shims.

4.Press bearing/bearing plate assembly onto rotor.

5.Check clearance between rotor and bearing plate by using a .001" feeler gauge. Clearance should be at .001" to .0015". Adjust clearance by repeating steps 2-4 with different shim if necessary.

6.Once proper rotor gap clearance is achieved, install well lubricated 01185 Blades (4) into rotor slots. Dynabrade recommends using their 95842 Air Lube.

7.Install cylinder over rotor/pinion. Be sure air inlet holes of cylinder face away from 53183 Front Bearing Plate.

8.Press 02649 Rear Bearing into 13440 Rear Bearing Plate. Press bearing/bearing plate assembly onto rotor. Be sure that pin and air inlet holes line up with pin slot and air inlet holes in cylinder.

Important: Fit must be snug between bearing plates and cylinder. If too tight, rotor will not turn freely. Rotor must then be lightly tapped at press fit end so it will turn freely while still maintaining a snug fit. A loose fit will not achieve the proper preload of motor bearings.

9.Secure motor housing in padded vise so motor cavity faces upwards. Install motor assembly into housing. Be sure motor inlet is facing the handle and it drops all the way into housing.

10.Press front 02552 Bearing onto front end of 53180 Planetary Carrier.

11.Apply #271 Loctite® to 53181 Spindle and install onto 53180 Planetary Carrier (torque 17.0 N•m/150 in. - lbs.).

12.Install gears, 04026 Bearings and 53182 Gear Shafts onto planetary carrier.

13.Slip 53191 Ring Gear over gears and press rear 02552 Bearing onto planetary carrier.

14.Apply two drops of #271 Loctite® to threads of 13432 Spindle Cover.

15.Apply #271 Loctite® to 13432 Spindle Cover and install onto housing, to secure motor (torque 28 N•m/250 in. - lbs.).

Motor Assembly Complete.

Housing Assembly:

1.Install 13438 Handle Grip. (Secure with #380 Loctite® or equivalent.)

2.Insert 13435 Valve Stem through housing and into hole in 13436 Bushing.

3.Insert 13439 Ball, 07145 Spring, 13437 Speed Regulator with 01024 O-Ring in place.

4.Install 13428 Packing onto 13427 Regulator Plug. Secure plug in place torque 8.5 N•m/75 in. - lbs.

5.Insert 94528 Muffler into 94522 Muffler Cap. Install 94521 Muffler Base onto muffler cap.

6.Install 95438 O-Ring into groove on muffler base. Place 95375 O-Ring and 94526 Spacer into recessed area of muffler cap.

(continued on next page)

53080 specifications

The Dynabrade 53080 is a powerful and versatile tool designed to enhance the efficiency of surface preparation and finishing tasks. This pneumatic hand-held sander is recognized for its robust construction, durability, and the ease it brings to various sanding applications. Built to cater to professionals in industries such as automotive, woodworking, and metal fabrication, the Dynabrade 53080 stands out with its impressive features.

One of the key characteristics of the Dynabrade 53080 is its unique random orbital sanding action. This feature allows for a swirl-free finish, an essential benefit for professionals seeking high-quality results without the risk of sanding marks. By utilizing a dual-action mechanism, the sander combines both rotary and orbital movements, allowing for efficient material removal while minimizing surface damage.

What makes the 53080 particularly effective is its pneumatic operation. This sander requires compressed air, which enables higher RPMs and a consistent power output. The tool effectively manages heat buildup, thereby extending its lifespan and enhancing performance during longer working periods. This characteristic is especially valuable in high-volume environments, where tools are subjected to repeated use.

Another noteworthy technology incorporated in the Dynabrade 53080 is its ergonomic design. The tool features a padded handle, ensuring a comfortable grip for extended use. This design consideration not only enhances user comfort but also minimizes fatigue during prolonged sanding tasks. Additionally, the lightweight nature of the tool increases maneuverability, allowing users to reach tight spaces and intricate areas that would typically be challenging to sand.

The Dynabrade 53080 is compatible with various sanding pads and abrasives, providing users with the flexibility to choose the right material for their specific tasks. This adaptability is particularly advantageous in settings that require a range of sanding techniques, from aggressive material removal to fine finishing.

Lastly, the sander is equipped with an integrated dust collection system. This feature helps to maintain a clean work environment by capturing dust and particles generated during sanding. By ensuring effective dust management, the Dynabrade 53080 not only promotes a safer workspace but also enhances visibility, allowing users to see their work clearly.

In summary, the Dynabrade 53080 is a well-engineered tool with prominent features such as its random orbital sanding action, pneumatic operation, ergonomic design, compatibility with various sanding materials, and an efficient dust collection system. These characteristics make it an excellent choice for professionals looking for both performance and precision in their sanding tasks.