Ryobi P211 manual Charging the Battery Pack, Charging a Cool Battery Pack

Page 11

OPERATION

CHARGING THE BATTERY PACK

Battery packs for this tool are shipped in a low charge con- dition to prevent possible problems. Therefore, you should charge them until the green LED on the front of the charger comes on.

NOTE: Batteries will not reach full charge the first time they are charged. Allow several cycles (operation followed by recharging) for them to become fully charged.

CHARGING A COOL BATTERY PACK

If battery pack is below normal temperature range, the green LED on charger will come on. Allow battery pack to reach normal temperature, then the red LED will come on.

NOTE: If the charger does not charge the battery pack under normal circumstances, return both the battery pack and charger to the nearest Sears Repair Center for electrical check.

nCharge the battery pack only with the charger provided.

nMake sure the power supply is normal household voltage, 120 volts, 60 Hz, AC only.

nConnect the charger to the power supply.

nPlace the battery pack in the charger aligning raised rib on the battery pack with the groove in the charger. See Figure 3.

nPress down on the battery pack to be sure contacts on the battery pack engage properly with contacts in the charger.

nNormally the red LED on charger will come on. This indi- cates the charger is in fast charging mode.

nRed LED should remain on for approximately 1 hour then the green LED will come on. Green LED on indicates battery pack is fully charged and charger is in maintenance charge mode.

NOTE: The green LED will remain on until the bat- tery pack is removed from the charger or charger is disconnected from the power supply.

nIf both yellow and green LEDs come on, this indicates a deeply discharged or defective battery pack. Al- low the battery pack to remain in the charger for 15 to 30 minutes. When the battery pack reaches normal voltage range, the red LED should come on. If the red LED does not come on after 30 minutes, this may indicate a defective battery pack and should be replaced.

nAfter normal usage, a minimum of 1 hour of charging time is required to fully recharge battery pack.

nThe battery pack will become slightly warm to the touch while charging. This is normal and does not indicate a problem.

 

P110

GREEN LED

CHARGER

 

YELLOW LED

RED LED

Fig. 2

BATTERY PACK SHOWN IN CHARGER

P110

CHARGER

P100

BATTERY PACK

Fig. 3

nDo not place the charger and battery pack in an area of extreme heat or cold. They will work best at normal room temperature.

NOTE: The charger and battery pack should be placed in a location where the temperature is more than 50°F but less than 100°F.

nWhen batteries become fully charged, unplug the charger from power supply and remove the battery pack.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction WarrantyPersonal Safety General Safety RulesWork Area Safety Electrical SafetyBattery Tool USE and Care Specific Safety RulesSafety Rules for Charger Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceProduct Specifications FeaturesAuxiliary Handle Quick Mode SelectorTorque Adjustment Ring Know Your Hammer DrillPacking List AssemblyOperation UnpackingCharging a Cool Battery Pack Charging the Battery PackBattery Pack Latches Charging a HOT Battery PackTo Install Battery Pack To Remove Battery PackLock Tighten Switch TriggerReverse Forward Unlock Release Switch Trigger Internal Spindle LockDrive Selecting Drive or Drill SettingQuick Mode Selector Choose Your ApplicationNot Active Application Speed ModeTorque Adjustment Torque AdjustmentBIT MAG Tray Unlock Release Chuck Jaws INSTALLING/REMOVING the Magnetic BIT HolderBits BIT Storage ScrewsSee Figures 14 Using the Auxiliary Handle AssemblyAdjusting the Auxiliary Handle Assembly Adjusting the Depth Stop RODChuck Unlock Release Installing BitsRemoving Bits SeeMasonry Drilling DrillingWood Drilling Metal DrillingBatteries MaintenanceGeneral Maintenance Battery Pack Removal Preparation for RecyclingMallet Chuck Jaws HEX KEY Chuck RemovalTo Retighten a Loose Chuck See Figures 18In./18 Volt Hammer Drill 2-SPEED
Related manuals
Manual 40 pages 58.33 Kb

P211 specifications

The Ryobi P211 is a versatile and powerful tool that stands out in the market of cordless drills. As part of Ryobi’s ONE+ system, this tool operates on an 18V battery platform, making it compatible with other Ryobi tools. This feature alone provides convenience and flexibility for users who want to minimize battery inventories.

One of the standout features of the P211 is its 1/2 inch single sleeve keyless chuck, which provides easy and quick bit changes. This functionality is especially useful for busy professionals and DIY enthusiasts who often switch between various tasks. Additionally, the drill boasts an impressive two-speed transmission, allowing users to select between 0-450 RPM for low speed and 0-1,600 RPM for high speed. This dual-speed capability is essential for tackling different materials and applications, from delicate tasks requiring precision to heavier projects demanding speed and torque.

Equipped with a powerful motor, the Ryobi P211 delivers a maximum torque of 350 in-lbs, enabling users to drive screws and drill into various materials such as wood, metal, and plastic with ease. The 24-position clutch adds further control to the tool, allowing users to adjust the torque setting based on the specifics of the job, thus preventing overdriving and damage to the materials being worked on.

User comfort is also a priority in the design of the Ryobi P211. The drill features a rubberized grip that not only provides a secure hold but also minimizes vibrations, making extended use more comfortable. Furthermore, the built-in LED work light illuminates dark workspaces, providing visibility in tight or dimly lit areas, which is crucial for precision work.

In terms of construction, the Ryobi P211 is built with durability in mind. Its rugged design ensures it withstands the rigors of daily use, appealing to both professionals and DIYers alike. The combination of features, power, and comfort makes the Ryobi P211 a reliable choice for a wide range of tasks, whether drilling pilot holes, driving screws, or working on home improvement projects. Overall, this tool embodies Ryobi's commitment to innovation and practicality, making it a valuable addition to any toolbox.
Top Page Image Contents