Ryobi BE318 manual Specific Safety Rules, Service, Additional Safety Rules

Page 4

GENERAL SAFETY RULES

SERVICE

￿Tool service must be performed only by quali- fied repair personnel. Service or maintenance per- formed by unqualified personnel could result in a risk of injury.

￿When servicing a tool, use only identical replace- ment parts. Follow instructions in the Mainte- nance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury.

SPECIFIC SAFETY RULES

Hold tool by insulated gripping surfaces when performing an operation where the tool may contact hidden wiring or its cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator.

ADDITIONAL SAFETY RULES

￿Know your power tool. Read operator’s manual carefully. Learn its applications and limitations, as well as the specific potential hazards related to this tool. Following this rule will reduce the risk of electric shock, fire, or serious injury.

￿Always wear safety glasses. Everyday eye- glasses have only impact-resistant lenses; they are NOT safety glasses. Following this rule will re- duce the risk of serious personal injury.

￿Protect your lungs. Wear a face or dust mask if the operation is dusty. Following this rule will re- duce the risk of serious personal injury.

￿Protect your hearing. Wear hearing protection during extended periods of operation. Following this rule will reduce the risk of serious personal in- jury.

￿Inspect tool cords periodically and, if damaged, have repaired at your nearest authorized service center. Constantly stay aware of cord location. Following this rule will reduce the risk of electric shock or fire.

￿Check damaged parts. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended func- tion. Check for alignment of moving parts, bind- ing of moving parts, breakage of parts, mount- ing, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center. Following this rule will reduce the risk of shock, fire, or serious injury.

￿Do not abuse cord. Never carry the tool by the cord or yank it to disconnect it from the recep- tacle. Keep cord away from heat, oil, and sharp edges. Following this rule will reduce the risk of elec- tric shock or fire.

￿Make sure your extension cord is in good condi- tion. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. A wire gage size (A.W.G.) of at least 16 is recommended for an extension cord 100 feet or less in length. A cord exceeding 100 feet is not recommended. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.

￿Inspect for and remove all nails from lumber be- fore using this tool. Following this rule will reduce the risk of serious personal injury.

￿Drugs, alcohol, medication. Do not operate tool while under the influence of drugs, alcohol, or any medication. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

￿Save these instructions. Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

lead from lead-based paints,

crystalline silica from bricks and cement and other masonry products, and

arsenic and chromium from chemically- treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

4

Image 4
Contents Operators Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Electrical SafetyPersonal Safety Work AreaService Specific Safety RulesAdditional Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONSpecifications UnpackingApplications InstructionsFeatures Features Operation Turning the Sander ON/OFFLocking on Selecting Sanding BeltsTo INSTALL/CHANGE Sanding Belts Using Sanding BeltsSee Figures 4, 5, See Figures 7 To Adjust Sanding Belt TrackingTurn Counterclockwise if Belt Runs Inward Using the Dust Collection BAG To Attach the Dust Collection BAGTo Empty the Dust Collection BAG Blower Exhaust Hole Dust BAG RetainerProper Hand Placement Operating the SanderGeneral MaintenanceHelpful Tips See Figures 12 Replacing the Timing BeltSmall Pulley Service Model NO. and Serial no