Ryobi P550 manual Squaring the Blade to the Miter Table, See Figures 25

Page 19

ASSEMBLY

SQUARING THE BLADE TO THE MITER TABLE

See Figures 25 - 28.

nRemove the battery pack from the tool.

nPull the saw arm all the way down and engage the lock pin to hold the saw arm in transport position.

nLift the miter table clamp.

nRotate the miter table until the pointer is positioned at 0°.

nPush the miter table clamp back down.

nLoosen bevel lock knob and set saw arm at 0° bevel (blade set 90° to miter table). Tighten bevel lock knob.

n Place a combination square against the miter table and the flat part of saw blade.

NOTE: Make sure that the square contacts the flat part of the saw blade, not the blade teeth.

nRotate the blade by hand and check the blade-to-table alignment at several points.

n The edge of the square and the saw blade should be parallel as shown in figure 25.

n If the top or bottom of the saw blade angles away from the square as shown in figures 26 and 27, adjustments are needed.

n Using a 10 mm wrench or adjustable wrench, loosen the lock nut securing positive stop adjustment screw. Also loosen bevel lock knob.

n Adjust positive stop adjustment screw to bring saw blade into alignment with the square. See Figure 28.

n Retighten bevel lock knob. Next, retighten lock nut securing the positive stop adjustment screw. Recheck blade-to-table alignment.

NOTE: The above procedure can be used to check blade squareness of the saw blade to the miter table at both 0° and 45° angles.

FENCE

 

 

 

 

 

 

455

 

 

 

 

 

 

30

 

 

 

 

 

15

BLADE

45

 

 

 

0

 

31.62

30

22.5

15

 

 

 

COMBINATION

 

 

 

MITER TABLE

SQUARE

 

 

 

 

 

VIEW OF BLADE NOT SQUARE WITH MITER

TABLE, ADJUSTMENTS ARE REQUIRED

Fig. 26

FENCE

 

 

 

 

 

 

45

 

 

 

 

 

 

5

 

 

 

 

 

 

30

 

 

 

 

 

15

BLADE

45

 

 

 

0

 

31.62

30

22.5

15

 

 

 

COMBINATION

 

 

 

MITER TABLE

 

 

 

 

SQUARE

 

 

 

 

 

VIEW OF BLADE NOT SQUARE WITH MITER

TABLE, ADJUSTMENTS ARE REQUIRED

Fig. 27

MITER TABLE

FENCE

POSITIVE STOP ADJUSTMENT SCREW FOR 0° ANGLES

15

30

 

 

 

 

 

 

45

 

 

 

 

 

 

5

 

 

 

 

 

 

30

 

 

 

 

 

15

BLADE

45

 

 

 

0

 

 

31.62

30

22.5

15

 

 

 

 

 

 

 

 

 

MITER TABLE

COMBINATION

SQUARE

VIEW OF BLADE SQUARE WITH MITER TABLE

Fig. 25

LOCK NUT(S)

POSITIVE STOP

ADJUSTMENT SCREW

FOR 45° ANGLES

Fig. 28

19

Image 19
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction Table of ContentsWork Area General Safety RulesElectrical Safety Personal SafetyService Specific Safety RulesSafety Rules for Charger Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning Anti-Kickback Pawls radial arm and table saws Glossary of TermsSee Figure FeaturesProduct Specifications Know Your Compound Miter SAWSpindle Lock Button Switch LockCarrying Handle Miter Table ClampTools Needed Work Clamp Loose PartsUnpacking AssemblyMounting Holes Dust BAG Dust GuideWork Clamp See Figures 13 To Install BladeTo Remove Blade See Figures 17 Squaring the Miter Table to the FenceSee Figures 21 Squaring the SAW Blade to the FenceSee Figures 25 Squaring the Blade to the Miter TableApplications Charging the Battery PackCharging a Cool Battery Pack OperationTo Install Battery Pack Charging a HOT Battery PackTo Remove Battery Pack See Figures 32 To CUT Small Molding and TrimTo Crosscut See Figures 35 To Bevel CUTTo Compound Miter CUT To Support Long Workpieces Cutting Compound Miters Laying Molding Flat on the Miter Table Cutting Crown MoldingClamping Wide Workpieces Cutting Warped MaterialSee Figures 41 Depth Stop Adjustments AdjustmentsPivot Adjustments Travel Pivot Adjustment Bevel Pivot AdjustmentBatteries MaintenanceGeneral Maintenance Battery Pack Removal and Preparation for RecyclingService Model NO. and Serial no