SECTION 7: WIRING
These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Study this diagram carefully. If you notice differences between your machine and these wiring diagrams, call Technical Support at (570) 546-9663 for assistance.
Electrical Safety Instructions
1.CIRCUIT REQUIREMENTS. You MUST fol- low the CIRCUIT REQUIREMENTS given on Page 9. If you are unsure about the wiring codes in your area or you plan to connect your machine to a shared circuit, consult a qualified electrician.
2.SHOCK HAZARD. Disconnect the power from the machine before servicing electrical components. Touching electrified parts will result in personal injury including but not lim- ited to severe burns, electrocution, or death.
3.MOTOR WIRING. The motor wiring shown in these diagrams are current at the time of printing, but it may not match your machine. Always use the wiring diagram inside the motor junction box.
4.EXPERIENCING DIFFICULTIES. If at any time you are experiencing difficulties under- standing the information included in this sec- tion, contact our Technical Support at (570) 546-9663.
NOTICE
The photos and diagrams included in this section are best viewed in color. You can view these pages in color at www.grizzly.com.
-22- | Model G4179 1⁄2 HP Power Feeder |
Power Feeder
Ss ,EAD from Leadbased PAINTS
Table of Contents
Introduction
Foreword Functional Overview
Contact Info
Machine Data Sheet
DiZg
Controls and features Model G4179 1⁄ 2 HP Power Feeder
Identification
!,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4
!,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29
BVXcZgn cdhZ XVc XVjhZ eZgbVcZci ZVgc\adhh#
53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2
53%3 2%#/--%.$%$- !##%33/2%3
-!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2
!,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#
Additional Safety for Power Feeders
220V Single-Phase
Circuit Requirements
Setup
Setup Safety
Items Needed for Setup
Unpacking
Inventory
Box Inventory Figures 3 Qty
Extra 26/34-Tooth Gears Behind Cover
Hardware Recognition Chart
Clean Up Assembly
Stand assembly
Base Mounting
ZcXZ 7aVYZ 8jiiZg
8jiiZgZVY
Mounting Options
Through-bolt mounting
Feed direction switch Model G4179 1⁄2 HP Power Feeder
Test Run
Operation Safety Basic Use and Care
Operations
Installed Change Gears
Included Accessory Change Gears
Changing Feed Speed
Turn the speed dial to the OFF position
Maintenance
Cleaning
Schedule
Lubrication
Service
Troubleshooting
Symptom Possible Cause Possible Solution
Wheel Replacement
Tools Needed Qty
To replace a wheel
Wiring
Electrical Safety Instructions
Wiring Diagram
Motor capacitors
Power Feed
Power Feed Parts List
Description
Base Parts List
Base
=dlYYndjaZVgcVWdjijh4 TTTT 6YkZgihZbZci Tttt gZcY
TTTT 8VgY9ZX` Tttt LZWhiZ TTTT DiZg
8VWcZiBV`Zg
IdYVn»h=dbZdlcZg
EaVXZ HiVbe =ZgZ
99.$5342!, .# 0//88 %,,.!- 7!
Warranty and Returns
#ALL 4ODAYD&ORO! &2%%