Safety Precautions
1.Read all instructions before using this tool. All operators must be fully trained in its use and aware of these safety rules.
2.The tool RPM should be checked on a regular basis (at shift change).
3.Make sure the tool is disconnected from the air supply. Attach the 3M™ Roloc™ Disc Pad to the sander adaptor using the wrenches supplied with the tool. Select a suitable abrasive and secure it to the back up pad.
4.Always wear required safety equipment when using this tool.
5.When sanding always start the tool just prior to contacting the work piece. Stop air flow to the tool as it is removed from the work piece.
6.Always remove the air supply to the sander before fitting, adjusting or removing the abrasive or disc pad.
7.Always adopt a firm footing and grip and be aware of torque reaction developed by the sander.
8.Use only 3M approved spare parts.
9.Always ensure the material being worked is firmly fixed to avoid movement.
10.Check hose and fittings regularly for wear. Do not carry the tool by its hose; always be careful to prevent the tool from being started when carrying the tool with the air supply connected.
11.If tool is serviced or rebuilt check to ensure that the maximum tool RPM is not exceeded and that there is no excessive tool vibration.
12.Dust can be highly combustible.
13.Do not exceed maximum recommended air pressure. Use safety equipment as recommended.
14.Prior to installing any sanding or polishing accessory, always check that it’s marked maximum operating speed is equal or higher than the rated speed of this tool.
15.The tool is not electrically insulated. Do not use where there is a possibility of contact with live electricity, gas pipes, and/or water pipes.
16.This tool is not protected against hazards inherent in grinding and cutting operations, which require a guard, and no such grinding and cutting products should ever be attached.
17.Take care to avoid entanglement with the moving parts of the tool with clothing, ties, hair, cleaning rags or loose hanging objects. If entangled, stop air supply immediately to avoid contact with moving tool parts.
18.Keep hands clear of the spinning pad during use.
19.If the tool appears to malfunction, remove from use immediately and arrange for service and repair.
20.Immediately release the start handle in the event of any disruption of pressure; do not attempt to
21.When tool is not in use, store in a clean dry environment free of debris.
22.Recycle or dispose of tool according to Local, State, and Federal regulations.
| Closed Loop Pipe System |
Drain Leg | Sloped in the direction of air flow |
| |
Ball Valve |
|
To Tool Station |
|
| Filter |
Ball | Regulator |
Valve | Lubricator |
|
| Ball Valve | Air Flow | |
|
| ||
| Drain Valve |
| |
|
| Air Dryer | |
| Air Hose |
| |
To Coupler | Air Compressor |
| |
at or near Tool |
| ||
and Tank | Figure 1 | ||
| |||
|
|
3M™ Roloc™ Disc Pads
3M™ Roloc™ Disc Pads are perfectly mated for use on the 3M Sander. Constructed from premium,
See 3M ASD Accessory catalog
Removing the sander adaptor and installing the
collet chuck
1.Disconnect air line from tool.
2.Using the wrenches supplied with the tool, secure the output shaft with one of the wrenches. Loosen the sander adaptor with the other wrench. Remove the sander adaptor and store in a safe place for use at another time.
3.Thread the collet chuck supplied with the tool into the threaded hole vacated by the sander adaptor.
4.Tighten the base of the collet chuck with the two wrenches.
5.Loosen the collar of the chuck to allow the appropriate shank to be inserted (¼ in collet insert is used for ¼ in shanks, 6 mm collet insert is used for
6 mm shanks).
6.Insert shank completely into the collet and tighten with the two wrenches. An inadequately inserted shank could bend or break causing damage to the tool and work piece and possible injury to the operator or bystanders.
7