Safety Warnings and Instructions: Sanders
•ALWAYS USE PROPER EYE and respiratory PROTECTION.
•Clean your tool out periodically.
Other Important Safety Warnings and Instructions
Sanding
Sanding Lead based Paint
Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of controlling the contaminated dust. The greatest danger of lead poisoning is to children and pregnant women.
Since it is difficult to identify whether or not a paint contains lead without a chemical analysis, we recommend the following precautions when sanding any paint:
PERSONAL SAFETY
• No children or pregnant women should enter the work area where the paint sanding is being done until all clean up is completed.
• A dust mask or respirator should be worn by all persons entering the work area. The filter should be replaced daily or whenever the wearer has difficulty breathing.
• NOTE: Only those dust masks suitable for working with lead paint dust and fumes should be used. Ordinary painting masks do not offer this protection. See your local hardware dealer for the proper (NIOSH approved) mask.
• NO EATING, DRINKING or SMOKING should be done in the work area to prevent ingesting contaminated paint particles. Workers should wash and clean up BEFORE eating, drinking or smoking. Articles of food, drink, or smoking should not be left in the work area where dust would settle on them.
ENVIRONMENTAL SAFETY
• Paint should be removed in such a manner as to minimize the amount of dust generated.
• Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mils thickness.
• Sanding should be done in a manner to reduce tracking of paint dust outside the work area.
CLEANING AND DISPOSAL
• All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the duration of the sanding project. Vacuum filter bags should be changed frequently.
• Plastic drop cloths should be gathered up and disposed of along with any dust chips or other removal debris. They should be placed in sealed refuse receptacles and disposed of through regular trash pick-up procedures. During clean up, children and pregnant women should be kept away from the immediate work area.
• All toys, washable furniture and utensils used by children should be washed thoroughly before being used again.
Motor
Be sure your power supply agrees with nameplate marking. 120 Volts AC only means your tool will operate on standard 60 Hz household power. Do not operate AC tools on DC. A rating of 120 volts AC/DC means that you tool will operate on standard 60 Hz AC or DC power. This information is printed on the nameplate. Lower voltage will cause loss of power and can result in over-heating. All Black & Decker tools are factory-tested; if this tool does not operate, check the power supply.
Save these instructions
Assembly/Adjustment Set-Up
CAUTION: To reduce the risk of injury, turn off and unplug the tool before making any adjustments or removing or installing attachments or accessories.
attaching 1/4 sheet sandpaper
• Lift clamps up with your thumb, (figure B). Rotate the clamp lever downward until the clamp is fully opened.
• Lay sandpaper on a flat surface and, centering the pad of the unit, press the sander down firmly onto the paper.
• Wrap ends of the sandpaper around ends of the sander pad and clamp them in place using the clamps.
• To close clamps, rotate clamp handles back up as far as they will go and lock them in place. Stretch sandpaper as tight as possible when clamping.
NOTE: On new tools the sandpaper may be difficult to install because of the stiffness of the sanding pad. This condition will improve as the pad compresses over time.
Punching sanding sheets
The paper punch is used for punching dust extraction holes in sanding sheets without pre-punched holes.
Attach a sanding sheet.
•Hold the tool in position directly above the paper punch.
•Press the tool with the sanding base down into the paper punch.
•Take the tool off the paper punch and check whether the holes in the sanding sheet have been fully pierced.
Operating Instructions
Warning: To reduce the risk of injury, let the tool work at its own pace. Do not overload.
WARNING: Shock hazard. Under no circumstances should this product be used near water.
Switch
To turn the tool ON, hold it as shown in figure C and push the portion of the switch marked “I”. To turn the tool off, push the portion of the switch marked “O”.
Operation
Grasp the sander as shown in figure D and turn it ON. Move it in long, sweeping strokes along the surface, letting it do the work. Pushing down on the tool while sanding actually slows the removal rate and produces an inferior quality finish.
Check your work often. Sander is capable of removing material rapidly especially with coarse paper.
• Circuit fuse is blown. | • Replace circuit fuse. |
| (If the product repeatedly |
| causes the circuit fuse to |
| blow, discontinue use |
| immediately and have it |
| serviced at a Black & |
| Decker service center or |
• Circuit breaker is tripped. | authorized servicer.) |
• Reset circuit breaker. |
| (If the product repeatedly |
| causes the circuit |
| breaker to trip, |
| discontinue use |
| immediately and have it |
| serviced at a Black & |
| Decker service center or |
• Cord or switch is damaged. | authorized servicer.) |
• Have cord or switch |
| replaced at Black |
| & Decker Service Center |
or Authorized Servicer |
For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest you or call the BLACK & DECKER help line at
1-800-544-6986.
fire, do not use your sander to sand magnesium surfaces. Do not use for wet sanding.
Maintenance
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts.
Accessories
Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call:
1-800-544-6986.
WARNING: The use of any accessory not recommended for use with this tool could be hazardous.
Service Information
All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under “Tools—Electric” or call:
1-800-544-6986 or visit www.blackanddecker.com
Full Two-Year Home Use Warranty
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned and authorized Service Centers are listed under “Tools- Electric” in the yellow pages of the phone directory and available on our website www. blackanddecker.com.
This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state. Should you have any questions, contact the manager of your nearest Black & Decker Service Center. This product is not intended for commercial use.
Free Warning Label Replacement: If your warning labels become illegible or are missing, call 1-800-544-6986for a free replacement.st Black & Decker Service Center.
Imported by | See ‘Tools-Electric’ |
Black & Decker (U.S.) Inc., | – Yellow Pages – |
701 E. Joppa Rd. | for Service & Sales |
Towson, MD 21286 U.S.A. | |
CAUTION: Respiratory hazard. 