Energy Tech Laboratories 8320, 6310, 5310 Service Call Verification, Fault Code Meaning of Code

Page 15

Service Call Verification

Before you make a service call, first determine if the problem is:

•Warranty Service

•Unit operation (power supply, water flow, or time clock adjustment)

NOTE: The MANUFACTURER IS NOT RESPON- SIBLE for these adjustments.

Power Supply

•Verify that all circuit breakers are reset and work- ing properly.

•If the temperature display or the Power lamp on the control panel still does not light, contact the installing dealer, since it may be a power problem requiring an electrician.

Water Flow

•Verify that the pool filter is clean to provide good flow.

•Verify that valves are properly positioned to allow adequate water flow through the unit.

•If the Water Flow lamp (analog models) on the control panel still does not light, and water is circu- lating in the pool, verify that all valves are positioned correctly.

Time Clock Adjustment

Verify that the time clock is set to permit the unit to run long enough to heat properly.

Fault Code

Meaning of Code

 

 

OFF

The desired programmed temperature point is lower than 60°F (15°C).

 

 

 

Shortage of refrigerant gas in the unit or faulty low pressure control. The unit will show

LP & LP3

(LP3) after 3 LP faults and shuts down the unit and pool pump for protection. If this occurs,

 

you should call for service.

 

 

HP & HP3

Low water flow in the unit or faulty high pressure control. Check water flow/backwash. The

unit will show (HP3) after 3 HP faults. This will stop the unit for protection.

 

 

 

 

Possible causes:

 

• The filter is in backwash position.

 

• The filter pump is stopped.

 

• The filter is dirty.

FLo & FL3

• Shortage of water to pool pump.

 

• FIL parameter must be set to activate pool pump.

 

• Water pressure switch must be adjusted or it is broken.

 

• The unit is in the protection mode and will show (FL3), press any key to restart the unit.

 

FL3 code will stop the unit and pool pump.

 

 

FS

Unit is in the defrosting cycle.

(The fan works but the compressor is stopped.)

 

 

 

- -

Keypad is pressing down on both buttons. Replace keypad.

 

 

Table C: Control Board Fault Codes — Digital Models

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Heat Pump Pool & Spa Heater Page Free Chlorine Must not Exceed 5 PPM Water ChemistryContents Or substantial property damage if ignored Introduction Installation ConsiderationsElectrical Connections Installation Clearances8320 38-1/2 Pressure Drop Water ConnectionsIndicator Lamps Analog Models Controls & Indicator Lamps Analog ModelsControls Digital Models System Start-UpSeasonal Start-Up or Annual Check Digital Controls Operating InstructionsMaintenance Summer ShutdownFreeze Protection Unit is RUNNING, but not Heating TroubleshootingFault Code Meaning of Code Service Call VerificationPlumbing Diagrams Pool Piping for Heat Pump Pool Heater and Gas Pool Heater Switch Wiring Diagram 208V/230V Single-Phase Analog ModelsCompressor FAN Motor Wiring Diagram 208V/230V Single-Phase Digital ModelsSPA / Remote / Pool Switch Wiring Diagram 208V/230V 3-Phase Analog ModelsWiring Information Wiring Diagram 208V/230V 3-Phase Digital ModelsInstalling a Remote Control Device on Digital Heaters Installing a Remote Control Device on Analog Heaters

5310, 6310, 8320 specifications

Energy Tech Laboratories has made significant strides in the energy sector with its innovative range of products, particularly the models 8320, 5310, and 6310. These energy solutions are designed to meet the increasing demand for efficient, sustainable power generation and management.

The Energy Tech Laboratories 8320 is renowned for its robust performance in renewable energy applications. This model features advanced photovoltaic technology that maximizes energy capture from sunlight, making it ideal for solar power systems. Its integrated smart inverter allows for seamless grid connectivity while ensuring optimal energy conversion. Additionally, the 8320 includes state-of-the-art monitoring capabilities, enabling users to track energy production and consumption in real time. Its compact design and lightweight materials make it suitable for residential rooftops, as well as commercial installations.

Moving on to the 5310 model, this powerhouse focuses on energy storage solutions. Equipped with high-capacity lithium-ion batteries, the 5310 is engineered to store excess energy generated during peak production times for later use. This feature is particularly beneficial for users seeking to maximize their energy efficiency by utilizing stored power during peak demand periods. The 5310 also boasts a user-friendly interface that simplifies the monitoring and management of energy consumption, offering insights that help users make informed energy decisions.

Lastly, the Energy Tech Laboratories 6310 model stands out for its innovative energy management system. This model employs artificial intelligence and machine learning algorithms to optimize energy distribution and usage across various applications. Its decentralized architecture allows for improved energy resilience, making it an excellent choice for large-scale industrial operations and smart grid implementations. With real-time analytics, the 6310 can adapt to changing energy demands, reducing waste and enhancing overall efficiency.

In summary, Energy Tech Laboratories has established itself as a leader in the energy tech sector with its 8320, 5310, and 6310 models. Each product features cutting-edge technologies and characteristics that cater to distinct aspects of energy generation, storage, and management. By harnessing the power of innovation, Energy Tech Laboratories is paving the way for a more sustainable future.
Top Page Image Contents