Operation
Operation / Cleaning / Disposal / Information
QOperation
QPreparing the device for use
The mains voltage at the mains socket must match that shown on the rating plate on the device. Devices marked with 230 V can also be operated at 220 V.
Caution! When using the device, never allow the ventilation slots to be covered.
Switching the appliance on:
jPush the ON / OFF switch 2 to the position “I”, “II” or “III”.
Switching the appliance off:
jPush the ON / OFF switch 2 to the position “0”.
Setting the air flow and temperature: With the temperature and air volume regulator 2 you have three different blower levels available. You can thus select an air volume and temperature setting suitable for the particular application:
Setting I | 250 l / min | 30 °C |
|
|
|
Setting II | 350 l / min | 400 °C |
Setting III | 600 l / min | 600 °C |
The
-Drying varnish / paint
-Cooling of heated workpieces
-Cooling the appliance before storage / changing the nozzles
Removing the heat shield:
Caution! The appliance must be completely cooled down before you remove or put on the heat protector.
Caution! Danger of burns! Do not touch the hot nozzle. When you are working with- out the heat shield 3 there is an increased risk of burns. Remove the heat shield 3 for working in particularly narrow spaces.
j Pull the heat protector 3 to the fore.
Use as
jAlways set the device down upright on a level surface, this will allow
·you to have both hands free
·the device to cool
QChanging the nozzle
Warning! Too much heat causes paints and plastics to ignite.
Danger! Do not inhale the resulting vapours.
Reflector nozzle 5 – for shaping plastic pipes or tubes (see Ill. B):
jPlace the reflector nozzle 5 on the outlet tube 4 .
jFill the pipe or tube with sand and ensure it is closed at both ends. This will prevent the pipe or tube from kinking.
jWarm the pipe evenly, in that you move it back and forth.
Protector nozzle 6 – for removing paint and varnish (see Ill. C):
jPlace the protector nozzle 6 on the outlet tube 4 .
jThe spatula shape of the nozzle ensures the air is properly directed. Use a separate spatula for removing paint or varnish.
Flat nozzle 7 – for detaching glues, softening paint (see Ill. D):
jPlace the flat nozzle 7 on the outlet tube 4 .
jDo not apply heat for too long a period, as burnt paint becomes much more difficult to re- move. Many glues can be softened by warm- ing. Glued connections can then be detached and excess glue removed.
Reducing nozzle 8 – for welding plastic:
jPlace the reducer nozzle 8 on the outlet tube 4 .
jUse the reducing nozzle 8 for
QFurther examples of uses in the house, car and garden
Defrosting water pipes:
Notice! It must not be used for thawing PVC pipes. Notice! It is often very difficult to tell the differ- ence between gas pipes and water pipes. If in doubt, ask a competent person.
Notice! Copper pipes are joined using tin solder and must not be heated above 200 °C.
jUse the reflector 5 to defrost water pipes.
Loosening a threaded connection:
jHeating the threaded connection carefully can often allow the connection to be released.
Removing weeds:
jThe hot air dries out the weeds and
Lighting barbecue charcoal:
Warning! Do not use methylated alcohol.
jCharcoal ignites in a few minutes.
Wax removal:
jYou can remove wax residues from skis / snow- board or from candle holders. Use the amount of care appropriate to the product.
QCleaning
Warning! Before carrying out work on the appliance, always remove the plug from the power socket.
jKeep the air inlet and outlet clean.
jUse a cloth to clean the housing. Use a soft cloth to clean the housing. Never use petrol, solvents or cleaning agents as these may attack the plastic.
QDisposal
The packaging is wholly composed of
centre.
Do not dispose of electric tools in the household waste!
In accordance with European Directive 2002 / 96 / EC relating to old electrical and electronic appliances and its translation into national law, used electric tools must be collected separately and recycled in an ecologically desirable way. Please contact your local council office to find out about disposal facili- ties for your
QInformation
QService
Details of the Service Centre responsible for your region are shown in the warranty documents.
JHave your device repaired only by qualified specialist personnel using original manufactur- er parts only. This will ensure that your device remains safe to use.
JIf the plug or mains lead needs to be replaced, always have the replacement carried out by the manufacturer or its service centre. This will ensure that your device remains safe to use.
10 GB/IE/CY
GB/IE/CY 11