Maintenance

Feeding Stock:

CAUTION: You should always use the push blocks with every operation. You must use the push blocks when working with stock that is less than 3” wide or thick.

CAUTION: Never feed with your hand on the end of the stock! Serious injury may result.

1.Always hold your stock firmly against the fence.

2.Always feed at an even rate along the entire length. Hesitations or stops will result in marred and uneven finishes. Do not feed too fast.

3.Apply even pressure. Start feeding with your left hand forward and your right a couple inches

behind. As your right hand passes over the blades, move your left hand behind the right. Continue shifting in this fashion until all of your stock has been planed.

Bevel Planing:

1.Set the fence to the desired angle.

2.Move the fence in or out along the table to accommodate the desired planing width.

3.Plane along the edge of the stock. Make sure you are pushing the sock firmly against the fence.

V-Belt Replacement:

1.Remove the Jointer Planer from the wooden base.

2.Remove the belt cover (29).

3.Turn the machine over. Remove the base screen (10) by unscrewing the six M4 x 12 screws

(8).

4.Remove the base (22) by removing the eight M5 x 30 screws (20). When lifting the base off, be careful not to loosen any of the attached wires.

5.Remove the V-belt by simultaneously turning and pulling outward on it.

6.Install the new V-belt by simultaneously turning and pushing inward on it.

7.Reattach the base, screen and belt cover. Reattach the Jointer Planer to the wooden base.

Brush replacement:

1.Follow steps 1 - 4 as described in V-Belt Replacement (above).

2.Remove the two brush caps (57-8) and remove the brushes (57-7). If they are worn past the indicator line, they must be replaced.

3.When installing the new brushes, guide the spring into the holder (57-6) and hold it in until the cap is in position.

4.Reattach the base, screen and belt cover. Reattach the Jointer Planer to the wooden base.

Fence Angle Adjustment Lever (52) adjustment:

If one of the Fence Angle Adjustment Levers (52) contacts the Fence (44) while tightening, preventing it from fully tightening, perform the following steps:

1.Loosen the Tapping Screw (54) enough so that the Fence Angle Adjustment Lever can turn without turning the Lock Bolt (46/51).

2.Turn the Fence Angle Adjustment Lever until it has enough room to travel to allow proper operation.

3.Make sure the Fence Angle Adjustment Lever (52) is pressed against the Lock Bolt (46/51) snugly. Tighten the Tapping Screw (54) securely. Test the fence for proper operation before use.

REV 02/04

SKU 34434

For technical questions, please call 1-800-444-3353.

Page 7

34434 specifications

Harbor Freight Tools offers an impressive range of tools and equipment for both professionals and DIY enthusiasts, and among its popular products is the 34434. This versatile tool has garnered attention for its reliability, affordability, and user-friendly features that cater to a varied audience.

The Harbor Freight Tools 34434 is a 20-gallon parts washer that provides an efficient and effective solution for cleaning automotive parts and components. Designed for convenience and performance, it is ideal for mechanics and hobbyists alike who need to maintain and restore their tools.

One of the key features of this parts washer is its large capacity. The 20-gallon tank can accommodate a wide variety of parts, allowing users to clean multiple items at once. The spacious interior reduces the need for multiple wash cycles, saving both time and effort.

Additionally, the 34434 includes a powerful pump system that circulates cleaning solvent through a drain hose and back into the tank, ensuring that contaminants are effectively washed away. This constant circulation helps to maintain a clean working environment and prolongs the life of the cleaning solution, making it a cost-effective option for users.

The design of the parts washer prioritizes ease of use. It features a built-in work surface, which allows users to easily place their parts for washing, while the adjustable spray nozzle provides users with control over the flow and intensity of the cleaning solution. This adaptability ensures that delicate parts can be cleaned thoroughly without the risk of damage.

Safety is also a significant consideration in the design of the 34434. It includes a splash guard to prevent cleaning solvent from spilling out of the tank, as well as an integrated lid that helps to limit fumes from escaping. These features work together to create a safer working environment.

In conclusion, the Harbor Freight Tools 34434 is an excellent investment for anyone in need of an efficient and reliable parts washer. With its ample capacity, powerful cleaning capabilities, user-friendly design, and safety features, it stands out as a go-to choice for automotive cleaning tasks. Whether for DIY projects or professional use, this tool meets a variety of needs, making it a valuable addition to any workshop.