Jet Tools JWP-16OS owner manual Power Feed, Depth Limiter, Initial Startup

Page 21

Figure 35

After the head assembly height is adjusted, tighten the two black knobs down again.

Power Feed

Referring to Figure 36:

The power feed features two feed rates, 16 FPM and 20 FPM. When running the machine, the operator can control the feed speed by moving the feed control knob. Moving the knob toward the machine produces the 20 FPM feed speed (A), away from the machine produces 16 FPM

(C)and a center position places the gear box in neutral (B).

Figure 36

Set the feed rate while the planer is running but before feeding lumber into it. DO NOT change speeds after the cutting operation has begun.

If the cut is too large, the planer will slow down considerably, possibly even stalling the motor. Turn off the power immediately, raise the head assembly and remove the workpiece. Re-adjust the head assembly to allow a lesser cut and repeat the operation.

Handwheel

Crank the handwheel to raise or lower the table according to the desired workpiece thickness.

Each complete revolution of the handwheel moves the head assembly by 0.158” (4mm). Make sure the height scale is properly adjusted.

With the depth-limiting clip installed, you cannot cut full width more than 1/8" in a single pass (3/16" if lumber can fit on either side of the depth limiting clip). While cutting this much material is possible, it is not recommended.

Depth Limiter

The Model JWP-16OS Planer is equipped with a depth limiter – located on the bottom of the cutterhead casting just below the warning label (A, Fig. 37). The depth limiter controls maximum depth of cut to 1/8".

Figure 37

To avoid mechanical damage to the planer, do not remove the depth limiter.

Initial Startup

After the assembly and adjustments are complete the planer is ready to be tested.

Turn on the power supply at the main panel. Press the Start button. Keep your finger on the Stop button in case of a problem. The planer should run smoothly with little or no vibration or rubbing noises. Investigate and correct the source of any problems before further operation.

DO NOT attempt to investigate or adjust the planer while it is running. Wait until the planer is turned off, unplugged and all working parts have come to a complete standstill.

Always wear ANSI-approved safety glasses or goggles when operating equipment.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents JWP-16OS Woodworking Planer Warranty Limited WarrantyMore Information Table of Contents Page Page Safety Decals JWP-16OS Features of the JWP-16OS Planer SpecificationsParts Inventory ReceivingAssembly Stand AssemblyPlaner Unit Placement Handwheel Starter BoxExtension Rollers Dust Collection HoodControl and Adjustments AdjustmentsElectrical Connections Extension CordsPulleys and Belts Pulley AlignmentBelt Tension Extension Roller Table RollersKnife Adjustment Depth of Cut AdjustmentRemoving and Replacing Knives Checking Work Table Parallel to Cutterhead Table AdjustmentAdjusting Work Table Parallel to Cutterhead Major Adjustment Adjusting Work Table Parallel to Cutterhead Fine AdjustmentInfeed & Outfeed Roller Spring Tension Adjustment Transmitting RollersAnti-Kickback Checking and Adjusting the Feed Roller Height Operation GearboxTable Locks Power Feed Depth LimiterInitial Startup Maintenance GeneralSharpening Knives Lubrication Optional Accessories Performance Troubleshooting TroubleshootingMechanical Troubleshooting Head Assembly Parts List for the JWP-16OS PlanerIndex No. Part No Description Size Quantity Head Assembly Parts ListJWP15H-007 Base Assembly Base Assembly Parts List BB-6202ZZ Gear Box Assembly Gear Box Assembly Parts List TS-1515021 Stand Assembly Stand Assembly Parts ListElectrical Schematic for JWP-16OS Planer WMH Tool Group

JWP-16OS specifications

The Jet Tools JWP-16OS is a high-performance woodworking planer designed for both professionals and hobbyists seeking precision and efficiency in their projects. This machine is notable for its robust construction and advanced features that facilitate smooth and accurate planing of wood surfaces.

One of the standout characteristics of the JWP-16OS is its powerful 3-horsepower motor, which delivers ample torque to handle even the most challenging wood species. This motor, paired with a six-knife cutter head, ensures a clean and finished surface while reducing the need for excessive sanding post-planing. The six knives provide a finer cut and smoother finish, making this planer suitable for a variety of woodworking applications.

Another significant feature is the proprietary Jet Air Systems technology that maintains a quiet operation, making the JWP-16OS suitable for any workspace without excessive noise. This technology minimizes vibration, further enhancing the overall precision and longevity of the machine. Additionally, the machine comes equipped with a built-in dust port, allowing for cleaner operation by connecting to a dust collection system, ensuring that your work environment remains as tidy as your finished projects.

The JWP-16OS also showcases an easily adjustable infeed and outfeed table, which provides extended support for larger workpieces. This feature greatly enhances the user’s ability to work with larger boards, contributing to an efficient workflow and minimized risk of material snags or defects. The combined table length of 84 inches aids in maintaining stability during operation.

Safety features are also a priority in the design of the JWP-16OS. It includes a safety disconnect switch to prevent accidental startups, ensuring that the machine is safe to operate at all times. The machine is engineered with user-friendly controls, allowing even novice woodworkers to operate it effectively with minimal learning curve.

In summary, the Jet Tools JWP-16OS is a powerful, feature-rich planer that delivers precision, efficiency, and safety. Its robust motor, advanced cutter head technology, quiet operation, and user-friendly design make it an excellent addition to any workshop. Whether for professional use or hobbyist endeavors, the JWP-16OS stands out as a reliable tool for achieving high-quality woodworking results.
Top Page Image Contents