Jet Tools JJP-10BTOS operating instructions Stand Assembly, Mounting Jointer-Planer to Stand

Page 10

Assembly

For assembly convenience, the item letter designators used throughout the Assembly section are the same as those used to identify shipping content and hardware components on pages 8–9.

Stand Assembly

Referring to Figure 5:

1.Select two legs (N),one short stand top support

(H)and one short support plate (E).

2.Attach one end of the stand top support (H) to the top of the first leg with two carriage bolts (Y), flat washers (CC), lock washers (DD) and hex nuts

(EE). Attach the other end of the stand top support (H) to the second leg in the same manner. Hand-tighten only at this time.

3.Attach a support plate (E) to each leg (N) in the same manner with two carriage bolts (Y), flat washers (CC), lock washers (DD) and hex nuts

(EE). Hand-tighten only at this time.

4.Repeat steps 1–3 using the remaining legs, short stand top support and support plate.

5.Complete the stand construction by attaching long stand top supports (G) and long support plates (D) to the leg assemblies constructed in steps 1–4. Hand-tighten all hardware only at this time.

6.Place a rubber foot (LL) on a hex cap screw (X), then insert the threaded end of the screw through the opening on the bottom of the leg.

7.Secure with flat washer (CC) and hex nut (EE).

8.Attach rubber feet to remaining legs in the same manner.

9.Place stand upright. Ensure that the stand is on a level surface and all four legs are contacting the surface.

10.Tighten all hex nuts with the 10mm wrench (O) provided.

Mounting Jointer-Planer to Stand

Referring to Figure 6:

1.Place the Jointer-Planer(F) onto the assembled stand and secure with 4 each socket head cap screws (BB), lock washers (KK), and flat washers (JJ).

2.Tighten all socket head cap screws (BB) with the 5mm hex wrench (Q) provided.

10

EE

DD CC

H

Y

 

EE DD CC E

Y

N

 

G

B

D EE

CC

LL

X

Figure 5

Figure 6

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Walter Meier Manufacturing Inc Part No. M-707410Warranty and Service More InformationTable of Contents Page Page Page Features Stock No DescriptionShipping Contents Knobs and Handles HardwareStand Assembly AssemblyMounting Jointer-Planer to Stand Jointer-Planer Assembly Jointer Setup Planer SetupPlaner Controls and Adjustments PowerOperating Controls Infeed Table Height Adjustment Jointer Controls and AdjustmentsFence Bevel Adjustment Determining if adjustment is necessary AdjustmentsCutterhead Knife Adjustment Adjustment procedureFence 45º Adjustment Jointer Fence AdjustmentFence 90º Adjustment Replacing Cutter KnivesFeed-roller Belt Replacement Belt ReplacementCutterhead Drive Belt Replacement Dust Collection Changing Mode of OperationBasic Operations Initial StartupDirection of Grain Edge JointingBeveling PrecautionsPlaner Operations Depth of CutFeeding the Work Preparing the WorkAvoiding Snipe Blade Care MaintenanceLubrication Sharpening the KnivesTrouble TroubleshootingPerformance Troubleshooting Jointer Probable Cause RemedyPerformance Troubleshooting Planer Mechanical Troubleshooting Planer/Jointer Trouble Probable Cause RemedyParts Ordering Replacement PartsJointer/Planer Parts List Index No Description Size QtyJJP8BT-50 Index No. Part No Description Size Qty JJP8BT-KSG JOINTER-PLANER Assembly Drawing Index Planer Table Assembly Motor Front Frame Assembly Chain Drive Assembly Front Cover Assembly Cutterhead Guard Assembly Dust Cover Assembly Jointer Infeed Table Assembly Jointer Outfeed Table Assembly Cutter Head/Feed Roller Assembly Jointer Fence Assembly Rear Frame and Cover Assembly Jointer/Planer Stand Electrical Connection New Sanford Road LaVergne, Tennessee Phone
Top Page Image Contents