Miller Electric Inverter Rack manual Installing Welding Power Source Onto Rack

Page 15

3-4. Installing Welding Power Source Onto Rack

1

2

For XMT 304/EX 300 And

For XMT 304/EX 300

XMT 456/Invision 456 Models

Models Only

Location of mounting holes

in bottom of base (both sides).

For XMT 456/Invision 456 Models Only

Have only qualified persons make this installation.

YTurn Off welding power sources before inspecting or installing rack.

For XMT 304/EX 300 Models

1 Welding Power Source

Position welding power source onto rack shelf so threaded holes in feet are over correct holes in shelf on rack (see illustration). Welding power source front panel should face side of rack with isolated ter- minal on base as shown.

2 Securing Bolts And Hardware

Install supplied bolts through rack shelf into welding power source feet and tighten.

For XMT 456 and Invision 456 Models

1 Welding Power Source

Position welding power source onto rack shelf so holes in base of welder align with correct holes in shelf on rack (see illustration). Welding power source front panel should face side of rack with iso- lated terminal on base as shown.

.The factory-supplied mount- ing hardware is for XMT 304/EX 300 models only. Do not attempt to use this hard- ware when installing an XMT 456 or Invision 456 onto rack.

Install user-supplied 1/4 in mount- ing bolt through holes in welding power source base and rack shelf and tighten user-supplied hard- ware to secure in place.

Holes 1 And 4

Holes 5 And 6

Holes 7 And 10

 

 

 

 

 

 

 

 

 

 

 

 

Mounting Hole

Pattern For

XMT 304/EX 300

Models

(Both Shelves)

Holes 2 And 5

Holes 6 And 9

Mounting

 

 

Shelves

Mounting Hole

Pattern For XMT

456/Invision 456

Models

(Both Shelves)

ST-801 192 / ST-801 696 / ST-801 698 / 802 260 / 802 537

OM-818 Page 11

Page 14 Page 16
Image 15
Page 14 Page 16
Contents OM-818 ProcessesDescription From Miller to You Table of Contents Page Electric Shock can kill Symbol UsageMarks a special safety message Arc Welding HazardsBuildup of GAS can injure or kill ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal can injure eyesCalifornia Proposition 65 Warnings Principal Safety Standards EMF InformationAbout Pacemakers − Consignes DE Sécurité − À Lire Avant Utilisation Identifie un message de sécurité particulierLE Bruit peut affecter l’ouïe LE Soudage peut causer un incen- die ou une explosionLES Particules Projetées peu- vent blesser les yeux LES Pièces Chaudes peuvent cau- ser des brûlures gravesLES Pièces Mobiles peuvent cau- ser des blessures Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser ’EMPLOI Excessif peut FairePrincipales normes de sécurité Information sur les champs électromagnétiquesConsignes relatives aux stimulateurs cardiaques Rack Specifications For Racks Used With XMT 304/EX 300 ModelsDimensions And Weight Selecting a LocationMovement Installing Welding Power Source Onto Rack For XMT 304/EX 300 ModelsFor XMT 456 and Invision 456 Models Input Conductors Power Circuit Breaker Terminals Welding Power Source Input Power ConnectionsARC Welding can cause Electromagnetic Interference Selecting Cable SizesCommon Work Connections Paralleling Welding Power Sources For Smaw Securely cover connection with proper insulating materialPosition of the welding cable connec- tors while welding Connecting Input Power To Rack Electrical Service Guide For XMT 304/EX 300 6-Racks Electrical Service Guide For XMT 304 4-Racks− Maintenance & Troubleshooting Overload Protection Troubleshooting− Electrical Diagrams 184 139-B − Parts List Support ServiceMiller Electric Mfg. Co Owner’s Record
Top Page Image Contents