Miller Electric XMT 400 manual 60 s

Page 16

1	2	3	4	5	6
			V		V
			V
			> 60 s	V	S-179 190-A

1Warning! Watch Out! There are possible hazards as shown by the symbols.

2Electric shock from wiring can kill.

3Disconnect input plug or power before working on machine.

4Hazardous voltage remains on input capacitors after power is turned off. Do not touch fully charged capacitors.

5Always wait 60 seconds after power is turned off before working on unit, OR

6Check input capacitor voltage, and be sure it is near 0 before touching any parts.

4/96

1

2

3

4

5

S-179 304-A

1Warning! Watch Out! There are possible hazards as shown by the symbols.

2When power is applied failed parts can explode or cause other parts to explode.

3Flying pieces of parts can cause injury. Always wear a face shield when servicing unit.

4Always wear long sleeves and button your collar when servicing unit.

5After taking proper precautions as shown, connect power to unit.

				4/96
			1	Warning! Watch Out! There
		1		are possible hazards as
		1		shown by the symbols.
			2	Falling equipment can cause
				injury and damage to unit.
			3	Always lift and support unit
				using both handles. Keep
				angle of lifting device less
	∠ = <60°			than 60 degrees.
	∠ = <60°		4	Use a proper cart to move
	∠			unit.
	∠		5	Do not use one handle to lift
			5	Do not use one handle to lift
				or support unit.
			S-179 309-A
2	3	4	5
				1/96
OM-217 769 Page 12

Image 16

Contents OM-217 769L ProcessesDescription File MultiprocessFrom Miller to You Table of Contents Page Symbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can cause severe burnsFumes and Gases can be hazardous ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal or Dirt can injure eyesWelding Wire can cause injury Fire or Explosion hazardFalling Unit can cause injury Moving Parts can cause injuryPrincipal Safety Standards California Proposition 65 WarningsEMF Information About Implanted Medical DevicesSymboles utilisés UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion LE Bruit peut endommager l’ouïe LES Bouteilles peuvent exploser si elles sont endommagéesRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesserLES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-217 769 Manufacturer’s Warning Label Definitions Disconnect input plug or power before working on machineKeep your head out of the fumes 60 s Symbols And Definitions Manufacturer’s Rating LabelI1max I1effSpecifications Duty Cycle And OverheatingCV Mode CC ModeVolt-Ampere Curves Dimensions And Weight Selecting a LocationWeld Output Terminals And Selecting Cable Sizes ARC Welding can cause Electromagnetic Interference350 ft 400 ft Put terminals Output ReceptaclesElectrical Service Guide Remote 14 Receptacle InformationTo a line terminal For Three-Phase Operation Connecting 3-Phase Input PowerYellow Conductor Power On/Off Switch Select setting best suited for applicationFront Panel Controls Inductance/Dig ControlMeter Functions Mode Switch Settings Lift-Arc TIG Procedure Touch Seconds Do not Strike Like a MatchDo not remove case when blowing out inside of unit Blowing Out Inside Of UnitVoltmeter/Ammeter Help Displays Troubleshooting Check, repair, or replace remote controlReset circuit breaker CB1 Remote 14 receptacle− Electrical Diagram − Parts List Dia Part Description Quantity PC3 219 Your distributor also gives ServiceSupport To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s