Setup, Lamp, Power, Gobo Holder | Chauvet TFX-FS360 manual

SETUP

Lamp

	You will need to install a lamp prior to the initial operation of the fixture. An ENX, 360 W halogen lamp
	is included.
Warning!	When replacing the lamp, please wait 15 minutes after powering down to allow the unit to cool
	down! Always disconnect from main power prior to lamp replacement.
	Do not touch the envelope (glass area) of the bulb with bare hands. If this happens, clean the lamp
	with alcohol and wipe it with a lint free cloth before installation.

L AMP INST ALL ATION

1)Remove screw located on the top and to the rear of the followspot as pictured on the right.

2)Open lamp cover until lamp compartment is exposed.

3)If replacing the lamp, remove old lamp first.

4)Reach in and slide the lamp out of the retaining cage.

5)Detach the lamp from the lamp socket and replace.

6)Replace lamp cover, align the screw hole and fasten the screw.

7)No lamp alignment is necessary for this fixture since the lamp is already optimized inside the reflector.

Power

Lamp Installation

Remove screw

Lamp exposed

Warning!	Verify that the power on your unit matches the line voltage applied. All fixtures must be
	connected to circuits with a suitable Ground.

∙To determine the power requirements for a particular fixture, see the label affixed to the back plate of the fixture or refer to the fixture’s specifications chart.

∙A fixture’s listed current rating is its average current draw under normal conditions.

∙All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100% switch.

∙Before applying power to a fixture, check that the source voltage matches the fixture’s requirement.

∙All fixtures must be connected to circuits with a suitable Ground.

Gobo Holder

The TFX-FS360 can project one gobo image. A gobo- holder is included and is located directly underneath the followspot next to the fan as pictured here on the right. Remove the two bottom screws from the gobo-holder and slide it out. You can remove the gobo by sliding it out the top and replacing it with a different one or replace gobo-holder without a gobo for followspot only use.

TFX-FS360 User Manual

2010-07-20/14:53

TFX-FS360 specifications

The Chauvet TFX-FS360 is a versatile two-in-one effect light specifically designed for mobile DJs, nightclubs, and live events. This powerful fixture combines the convenience of a wash light with the engaging dynamics of an effective effect light, making it an essential tool for enhancing any performance or event atmosphere.

One of the standout features of the TFX-FS360 is its dual functionality. It is equipped with a powerful wash LED that produces a wide and even color projection, ensuring that venues are lit brightly and vibrantly. The wash feature can be used to create immersive backgrounds or highlight specific areas within a space, providing flexibility in design and execution.

In addition to its wash capabilities, the TFX-FS360 incorporates a brilliant rotating gobo effect. With a variety of patterns and colors, this gobo projection can create compelling visuals on walls, floors, and ceilings, captivating audiences and setting the mood for any occasion. This combination of wash and gobo effects gives users the ability to create dynamic light shows that engage and energize party-goers.

The fixture boasts advanced LED technology, ensuring it delivers consistent color mixing and high brightness, all while being energy-efficient. The long lifespan of the LEDs reduces maintenance needs, making the TFX-FS360 a cost-effective solution for lighting. With a total output of 60 watts, users can expect powerful illumination without sacrificing energy efficiency.

User-friendly controls allow for easy operation of the TFX-FS360. It includes options for DMX control, enabling compatibility with sophisticated lighting designs. Alternatively, the fixture can operate in standalone mode or be set to sound activation, seamlessly synchronizing with the beat of any music. Additionally, multiple preset functions and automated programs offer flexibility for users of all experience levels.

The lightweight and durable design of the TFX-FS360 makes it easy to transport, set up, and break down, crucial factors for those on the road. With the added benefit of multiple mounting options, this fixture can be easily integrated into existing setups.

Overall, the Chauvet TFX-FS360 stands out as a powerful, multifunctional lighting fixture that brings versatility and creativity to any event. With its innovative technologies and user-friendly design, it is an excellent choice for lighting professionals and enthusiasts alike.