Sanyo VCC-9684VA Remove the dome cover, Remove the blue tape, air cushion and screw, Sync setting

Page 2

INSTALLATION

Español Français English

ADJUSTING CAMERA IMAGE

1Remove the dome cover.

Push

Preparation

2Remove the blue tape, air cushion and screw.

Do not touch the lens and lens barrel. 3Turn the lens

90 degrees

4Screw

clockwise.

 

5Loosen the black screw.

b Checks on monitor

Connect a portable monitor.

MONITOR

OUT

GND

Camera adjustments/settings

The camera comes pre-adjusted and ready to install at the time of factory shipment, but you can make adjustments or settings if you need.

If you have trouble adjusting the camera, consult your dealer or an Authorized Sanyo Service Center.

1Blue tape

2Air

cushion

A dedicated MONITOR OUT connector is provided for portable monitor.

bAngle-of-view adjustment

●Electronic shutter speed setting

(unit: second)

1/60

1/100

1/1000

1/2000

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

2

1

2

1

2

1

2

Switch1: MSB Switch2: LSB

●White balance (color compensation)

Manual White Balance

Auto-Tracing

White balance

 

(ATW)

 

 

 

MWB

6

6

A Installing on the Ceiling

1Connect the cables from the ceiling.

2Mount the camera unit to the base plate.

2

1

Power cables

B Installing on the Wall

1Set the lens in the correct direction.

1Remove the black screw A.

2Turn the lens in the arrow direction to reverse the orientation.

3Confirm that the dials are located at the top.

4Temporarily tighten the removed black screw A.

2

3

14

Adjust the angle of view by moving the lens unit.

200

(Ceiling Installed)

(Wall Installed)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

●Do not touch the lens and lens barrel.

● When rotating the lens unit, make sure a metal edge does not damage the cables.

•Using the high speed electronic shutter indoors with low lighting, will give darker pictures. In such a case, add some lights to make sure the lighting is sufficient.

•If the lighting is very bright, pay attention to the light angle in order to avoid or minimize the smear phenomenon effect.

●Aperture compensation

Sharp outline

Normal outline

 

 

 

 

 

 

 

 

 

 

 

 

3

3

●Backlight compensation

Only when using an auto-iris lens

RED

BLUE

Turn clockwise to augment the color.

●Sync setting

Line-Lock

 

 

 

Synchronizes the unit with

Internal sync

power frequency*

 

 

 

 

 

 

 

LL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

PHASE

7

 

 

*Adjust the roll by turning the LINE PHASE dial on the second and subsequent cameras.

If the vertical roll cannot be corrected by adjusting the LINE PHASE dial on the second and subsequent cameras, try adjusting the LINE PHASE dial on the first camera. If it still cannot be corrected, please check that the polarity of the power cords of all connected devices is correct.

Push the camera unit until it clicks taking care not to pinch the cable.

ABlack screw

2Connect the cables from the wall.

3Mount the camera unit to the base plate.

b Zoom and focus

 

B

 

A

D C

 

1Zoom

2Focus

Loosen the zoom ring

Loosen the focus ring

Multi-spot metering

 

High

Normal

Backlight compensation

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

to the entire screen*

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

5

 

 

 

4

 

5

 

 

 

 

 

 

 

 

 

 

 

 

 

Center zone metering

 

 

 

 

 

 

 

 

 

 

 

Backlight compensation

 

 

 

 

 

 

 

 

 

 

 

to the central portion of

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

5

 

 

 

 

the screen

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

5

 

 

 

 

*If the background of the object is extremely dark, set to Center zone metering.

●Lens iris level adjustment

If the entire image is too dark or too bright, adjust the condition.

A. I. LENS

Low (darker) High (brighter)

LEVEL

Supplied screw

Make sure that the camera unit and base plate fit perfectly.

2

Supplied screw

Push the camera unit until it clicks taking care not to pinch the cable.

3

Make sure that the camera unit and base plate fit perfectly.

knob A, and turn the

knob C, and turn the

zoom ring B to zoom in

focus ring D to focus on

or out.

the object.

When finished, tighten the zoom and focus ring knobs AC securely.

When monitoring lighting or other extremely bright objects (which exceed the maximum required illumination), smearing may occur in the vertical or horizontal direction (either above and below the high-brightness object or as a perpendicular band). In such a case, adjust the angle of illumination and other factors while observing the monitor.

After finishing camera adjustments/settings ...

1Tighten the screw.

2Install the dome cover.

 

1Push the dome cover until it clicks.

 

1

 

1

For wall installation, securely tighten the

 

screw you temporarily tightened.

2

 

2While holding down the dome cover, turn it

 

in the direction of the arrow until the lens is

 

completely visible through the camera

 

window.

Page 1 Page 2
Image 2
Page 1 Page 2
Contents Dimensions Φ151 104 Φ100 Case of a problemBe careful when handling the unit Do not install this unit close to magnetic fieldsLens iris level adjustment Electronic shutter speed settingSync setting 1Tighten the screw 2Install the dome cover

VCC-9684VA specifications

The Sanyo VCC-9684VA is a high-performance surveillance camera designed for a variety of security applications. With its advanced technological features, this device is particularly suitable for environments that require detailed monitoring and enhanced image quality.

One of the standout features of the VCC-9684VA is its 1/3-inch IT CCD sensor, which ensures exceptional image clarity and low-light performance. This sensor allows the camera to capture high-resolution video, making it easier to identify subjects in both day and night conditions. Coupled with its low-light sensitivity, the camera can deliver clear footage even in environments with minimal lighting, enhancing overall security capabilities.

The Sanyo VCC-9684VA supports a range of resolutions, including a maximum of 540 TV lines of horizontal resolution. This level of detail is crucial for capturing important footage, such as license plates or facial features, which can be essential in identification or evidence collection. Additionally, the camera has a built-in digital noise reduction feature that helps eliminate graininess in low-light conditions, further improving image quality.

Enhanced features include a programmable pre-sets functionality that allows users to configure specific monitoring areas. This feature enables the camera to cover larger spaces effectively without needing constant manual adjustments. The VCC-9684VA also supports multiple lens options, providing users with the flexibility to choose the appropriate focal length for various surveillance scenarios.

The camera is built with durability in mind, housing a robust casing that can withstand harsh weather conditions and vandalism. This makes the VCC-9684VA suitable for both indoor and outdoor installation in a multitude of settings, such as retail spaces, parking lots, and corporate environments.

Connectivity is another important aspect of the Sanyo VCC-9684VA. It supports standard video output formats, making integration with existing security systems straightforward. Moreover, it is compatible with various video management software options, enhancing its usability across different platforms.

In conclusion, the Sanyo VCC-9684VA combines high-performance imaging capabilities, adaptability with lens options, and robust construction, making it a compelling choice for comprehensive security solutions. Its advanced technological features, such as programmable presets and low-light performance, ensure it meets the demanding requirements of modern surveillance applications.
Top Page Image Contents