Humminbird G 12SE English, General Operational Precautions, Precautions on Using Disc Grinder

GENERAL OPERATIONAL PRECAUTIONS

1.Keep work area clean. Cluttered areas and benches invite injuries.

2.Consider work area environment. Don’t expose power tools t o rain. Don’t use power tools in damp or wet locations. Keep work area well lit.

Don’t use tools in presece of flammable liquids or gases.

Power tools produce sparks during operation. They also spark when switching ON/OFF. Never use power tools in dangerous sites containing lacquer, paint, benzine, thinner, gasoline, gases, adhesive agents, and other materials which are combustible or explosive.

3.Guard against electric shock. Prevent body contact with grounded surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.

4.Kep children away. Do not let visitors contact tool or extension cord. All visitors should be kept away from work area.

5.Store idle tools. When not in use, tools should be stored in dry and high or locked-up place—out of reach of children.

6.Don’t force tools. It will do the job better and safer at the rate or which it was intended.

7.Use right tool. Don’t force small tool or attachment to do the job of a heavy—duty tool. Don’t use tool for purpose not intended—for example—don’t use circular saw for cutting tree limbs or logs.

8.Dress properly. Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and non-skid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair.

9.Use safety glasses. Also use face or dust mask if cutting operation is dusty.

10.Don’t abuse cord. Never carry tool by cord or yank it do disconnect from receptacle. Keep cord from heat, oil and sharp edges.

11.Secure work. Use clamps or a vise to hold work. It’s safer than using your hand and it frees both hands to operate tool.

12.Don’t overreach. Keep proper footing and balance at all times.

13.Maintain tools with care. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service center. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean, and free from oil and grease.

14.Disconnect tools. When not in use, before servicing, and when changing accessories, such as blades, bits, cutters.

15.Remove adjusting keys and wrenches. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on.

16.Avoid unintentional starting. Don’t carry plugged- in tool with finger on switch. Be sure switch is off when plugging in.

17.Outdoor use extension cords. When tool is used outdoors, use only extension cords intended for use for outdoors and so marked.

English

18.Stay alert. Watch what you are doing. Use common sense. Do not operate tool when you are tired.

19.Check damaged parts. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual. Have defective switches replaced by authorized service center. Do not use tool if switch does not turn it on and off.

20.Do not use power tools for applications other than those specified in the Handling Instructions.

21.To ensure the designed operational integrity of power tools, do not remove installed covers or screws.

22.Do not touch movable parts or accessories unless the power source has been disconnected.

23.Use your tool at lower input than specified on the nameplate; otherwise, the finish may be spoiled and working efficiency reduced due to motor overload.

24.Do not wipe plastic parts with solvent. Solvents such as gasoline, thinner, benzine, carbon tetrachloride, alcohol, ammonia and oil containing chloric annex may damage and crack plastic parts. Do not wipe them with such solvent. Wipe plastic parts with a soft cloth lightly dampened with soapy water.

25.Consult an authorized Service Agent in the event of power tool failure.

26.Use only genuine HITACHI replacement parts.

27.This tool should only be disassembled for replacement of carbon brushes.

PRECAUTIONS ON USING DISC GRINDER

1.This product shall be applied to industrial use.

2.Never operate these power tools without Wheel Guards.

3.Use only grinding wheels with a “Safe Speed” at least as high as the “No-Load Speed” indicated on the power tool nameplate.

4.Always hold the body handle and side handle of the power tools firmly. Otherwise the counterforce produced may result in inaccurate and even dangerous operation.

5.Never depress the push button while the spindle is turning.

15