Genesis Advanced Technologies GBG800L manuel dutilisation Extension Cords, Service

Page 5

Feed the work piece in the correct direction and speed. Feed the work piece into a blade, cutter, or abrasive surface against the direction of the cutting tool’s direction of rotation only. Incorrectly feeding the work piece in the same direction may cause the work piece to be thrown out at high speed.

Never leave the tool running unattended, turn the power off. Do not leave the tool until it comes to a complete stop.

Never start the power tool when any rotating component is in contact with the work piece.

SERVICE

Have Your Power Tool Serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Service Your Power Tool periodically. When cleaning a tool, be careful not to disassemble any portion of the tool since internal wires may be misplaced or pinched.

WARNING:

READ AND UNDERSTAND ALL WARNINGS, CAUTIONS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.

English

EXTENSION CORDS

Grounded tools require a three wire extension cord. Double insulated tools can use either a two or three wire extension cord. As the distance from the power supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. Refer to the table shown below to determine the required minimum wire size.

The smaller the gauge number of the wire, the greater the capacity of the cord. For example: a

14-gauge cord can carry a higher current than a 16-gauge cord. When using more than one extension cord to make up the total length, be sure each cord contains at least the minimum wire size required. If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum wire size.

Guidelines for Using Extension Cords

If you are using an extension cord outdoors, be sure it is marked with the suffix “W-A” (“W” in Canada) to indicate that it is acceptable for outdoor use.

Be sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it.

Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.

Recommended Minimum Wire Gauge for Extension Cords (120 Volt)

Nameplate

Extension Cord Length

 

 

 

 

 

Amperes

25 Feet

 

50 Feet

75 Feet

100 Feet

150 Feet

200 Feet

(At Full Load)

 

 

 

 

 

 

 

 

0–2.0

18

 

18

18

18

16

16

 

 

 

 

 

 

 

 

2.1–3.4

18

 

18

18

16

14

14

 

 

 

 

 

 

 

 

3.5–5.0

18

 

18

16

14

12

12

5.1–7.0

18

 

16

14

12

12

10

 

 

 

 

 

 

 

 

7.1–12.0

18

 

14

12

10

8

8

12.1–16.0

14

 

12

10

10

8

6

 

 

 

 

 

 

 

 

16.1–20.0

12

 

10

8

8

6

6

5

Image 5
Contents Bench Grinder with Lights Bench Grinder with Lights General Safety RulesPersonal Safety Work Area SafetyElectrical Safety Tool USE and Care Extension Cords ServiceSpecific Safety Rules for Bench Grinders Always keep hands and fingers away from rotating attachments Your 8 Bench Grinder Unpacking and Content Attaching and Adjusting Tool Rests ,6 Attaching and Adjusting Spark Guards and Eye Shields ,4Changing the Grinding Wheels FIG Mounting Bench GrinderBasic Grinder Operations OperationSharpening Twist Drill Bits Lawn Mower BladesCleaning MaintenanceSharpening Wood Chisels & Plane Irons Refurbishing Screwdriver TipsTOLL-FREE Help Line TWO-YEAR Warranty