Grizzly G0596 owner manual Additional Safety Instructions for Grinders

Page 8

Additional Safety Instructions for Grinders

1.EYE PROTECTION. Grinding ejects small particles at a high rate of speed. ALWAYS wear safety glasses when using this machine.

2.MOUNTING TO BENCH/STAND. An unse- cured grinder may become dangerously out of control during operation. Make sure grinder is FIRMLY secured to a bench/ stand before use.

3.WHEEL SPEED RATING. Wheels oper- ated at a faster speed than rated for may break or fly apart. Before mount- ing a new wheel, be sure the wheel RPM rating is equal or higher than the speed of the grinder.

4.WHEEL FLANGES. Only use the flanges included with the grinder when mounting wheels. Other flanges may not properly secure the wheel and cause an accident.

5.RING TEST. Perform a "ring test" on grind- ing wheels before installation to ensure that they are safe to use. A wheel that does not pass the ring test may break or fly apart during operation.

6.STARTING GRINDER. If a wheel is dam- aged, it will usually fly apart shortly after start-up. To protect yourself, always stand to the side of the grinder when turning it ON and allow it to run a full minute before standing in front of it.

7.LUNG PROTECTION. Grinding produces hazardous dust, which may cause long- term respiratory problems. Always wear a NIOSH–approved dust mask or respirator when grinding.

8.SIDE GRINDING. Grinding on the side of wheels can cause the them to break and fly apart—unless the wheel is rated for side grinding.

9.TOP GRINDING. Grinding on the top of wheels greatly increases the risk of workpiece kickback. Always grind on the downward part of the wheel.

10.HAND/WHEEL CONTACT. Grinding wheels can remove a lot of skin fast. Keep a firm grip on the workpiece and position your hands a safe distance away when grinding. DO NOT wear gloves as they may get caught in the grinding wheel and cause even more serious injuries.

11.TOOL REST POSITION. If the tool rest is too far away from the wheel, the workpiece may be pulled down, causing loss of con- trol and pulling your hand into the grinding wheel. Keep the tool rest within 18" from the wheel when operating.

12.CRACKED WHEEL. Cracked wheels may break and fly apart during operation. Replace cracked wheels immediately!

Like all machinery there is potential danger when operating this machine. Accidents are frequently caused by lack of familiarity or failure to pay attention. Use this machine with respect and caution to lessen the pos- sibility of operator injury. If normal safety precautions are overlooked or ignored, seri- ous personal injury may occur.

-6-

No list of safety guidelines can be complete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this and other machinery with caution and respect. Failure to do so could result in serious per- sonal injury, damage to equipment, or poor work results.

G0596-G0599 Industrial Bench Grinders

Image 8
Contents Model Page Table of Contents Contact Info IntroductionForeword Identification G0596 G0597 G0598 G0599Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Grinders Circuit Requirements OperationExtension Cords Phase ConverterGrounding SET UP Set Up SafetyItems Needed for Set Up UnpackingWhen locating your grinder, remember InventoryMountingEye Shields Box QtyTo test run the grinder Dust Collection Test RunTo connect a dust collection hose Hardware Recognition Chart Here are some tips to keep in mind while grinding Operation Safety Grinding TipsOperations Basic format for wheel numbering is Wheel Care Wheel SelectionHere are some tips to help you avoid breaking the wheel To perform a Ring Test Wheel InspectionWheel Dressing Wheel Replacement To replace a grinding wheelAccessories G0598 Replacement WheelsService Troubleshooting110V Wiring Diagram G0596 Single Phase 220V Wiring Diagram G0597/G0598 Single Phase 220V Wiring Diagram G0599 Phase Main Parts Breakdown Shield Parts List G0596-G0597 DescriptionParts List G0598-G0599 Wheel CoverWarranty and Returns Page Page