Craftsman 315.17513 owner manual PROTECTYOURHEARING,Wear hearing

• PROTECTYOURHEARING,Wear hearing

protection during extended periods of operation.

•DO NOT ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle, Keep cord from heat, oil, and sharp edges.

•SECURE WORK. Use clamps or a vise to hold work. It is safer than using your hand and it frees both hands to operate tool.

•DO NOT OVERREACH. Keep proper footing and balance at all times. Do not use on a ladder or unstable support. Secure tools when working at elevated positions.

•MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accesso- ries.

•DISCONNECT TOOLS. When not in use, before servicing, or when changing attachments, tools should be disconnected from power supply.

•REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of cl_cking to see that keys and adjusting wrenches are removed from tool before turning it on.

•AVOID ACCIDENTAL STARTING. Do not carry plugged-in tool with finger on switch. Be sure switch is off when plugging in.

•MAKE SURE YOUR EXTENSION CORD IS IN GOOD CONDITION. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. A wire gage size (A.W.G.) of at least 14 is recommended for an extension cord 100 feet or less in length. A cord exceeding 100 feet is not recommended. If in doubt, use the next heavier gage, The smaller the gage number, the heavier the cord.

•OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords suitable for use outdoors. Outdoor approved cords are marked with the suffix W-A, for example - SJTW.A or SJOW-A.

•KEEP CUTTERS CLEAN AND SHARP. Sharp cutters minimize stalling and kickback.

•KEEP HANDS AWAY FROM ROUTING AREA. Keep hands away from cutters. Do not reach under- neath work while cutter is rotating. Do not attempt to remove material while cutter is rotating.

•NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could ignite fumes.

•INSPECT TOOL CORDS PERIODICALLY and if damaged, have repaired at your nearest Sears

Repair Center. Stay constantly aware of cord location.

•INSPECT EXTENSION CORDS PERIODICALLY and replace if damaged.

•KEEP HANDLES DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products, or any strong solvents to clean your tool.

•STAY ALERT AND EXERCISE CONTROL. Watch what you are doing and use common sense. Do not operate tool when you are tired. Do not rush.

•CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center.

•DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by an authorized service center.

•INSPECT FOR and remove all nails from lumber before routing.

•DO NOT operate this tool while under the influence of drugs, alcohol, or any medication.

•POLARIZED PLUGS. To reduce the risk of electric shock, this tool has a polarized plug (one blade is wider than the other). This plug will fit in a polar- ized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

•WHEN SERVICING USE ONLY IDENTICAL CRAFTSMAN REPLACEMENT PARTS.

•WHEN USING THIS ROUTER WITH A ROUTER TABLE, HELP PREVENT POSSIBLE SERIOUS INJURY BY KEEPING THE CUTTER GUARDED AT ALL TIMES. Use only router tables, with guards, that have been designed for use on routers that are of this type, size, and weight.

•DO NOT USE TOOL UNDER "BROWNOUT" OR OTHER LOW VOLTAGE CONDITIONS. Also, do not use with any device that could cause the power supply voltage to change.

•SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also.