D-Link DIR-827 manual 802.11n/g 5GHz, Rate

Page 38

Section 3 - Configuration

802.11n/g (5GHz)

Enable Wireless: Check the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions.

Schedule: Select the time frame that you would like your wireless network enabled. The schedule may be set to Always. Any schedule you create will be available in the drop-down menu. Click Add New to create a new schedule.

Wireless Service Set Identifier (SSID) is the name of your wireless network.

Network Name: Create a name using up to 32 characters. The SSID is case-sensitive.

802.11Mode: Select one of the following:

802.11a Only - Select if all of your wireless clients are 802.11a. Mixed 802.11n and 802.11a - Select if you are using both 802.11n and 802.11a wireless clients.

802.11n Only - Select only if all of your wireless clients are 802.11n.

Enable Auto The Auto Channel Scan setting can be selected to allow the DIR-827

Channel Scan: to choose the channel with the least amount of interference.

Wireless Indicates the channel setting for the DIR-827. By default the channels set to 6. The Channel can be changed to fit the channel setting Channel: for an existing wireless network or to customize the wireless network. If you enable Auto Channel Scan, this option will be greyed out.

Transmission Select the transmit rate. It is strongly suggested to select Best (Auto) for best performance.

Rate:

Channel Width: Select the Channel Width:

Auto 20/40 - This is the default setting. Select if you are using both 802.11n and non-802.11n wireless devices. 20MHz - Select if you are not using any 802.11n wireless clients.

Visibility Status: Select Invisible if you do not want the SSID of your wireless network to be broadcasted by the DIR-827. If Invisible is selected, the SSID of the DIR-827 will not be seen by Site Survey utilities so your wireless clients will have to know the SSID of your DIR-827 in order to connect to it.

Wireless Security: Refer to page 91 for more information regarding wireless security.

D-Link DIR-827 User Manual

33

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Page Initial release PrefaceRevision Date Description Table of Contents Configure Wireless Security 115 Troubleshooting 111Warranty 123 Registration 129 117ProductPackageOverviewContents Browser Requirements System RequirementsComputer with the following Introduction Total PerformanceFeatures Other Features Include Hardware Overview ConnectionsFront View LEDs Installation Before you BeginWireless Installation Considerations Getting Started Configuration Quick Setup WizardPage Page Page Page Page Page Page Web-based Configuration Utility Setup Wizard Click Wireless Connection Setup Wizard to begin. Skip toPage Page Page Manual Configuration/Internet Setup Dynamic CablePPPoE DSL Reconnect Mode Select either Always-on,On-Demand, or Manual PptpAddress Address ModeUsername Password Reconnect Mode DNS ServersStatic assigned by ISP MAC AddressDS-Lite GatewayWireless Connection Setup and skip to the next Wireless SettingsAdd Wireless Device with WPS and skip to 802.11n/g 2.4GHz Rate802.11n/g 5GHz RateNetwork Settings IP Address Subnet MaskDhcp Server Settings NetBIOS ScopeDhcp Reservation Dynamic Dhcp IP addresses ClientsMedia Server Click IPv6 Internet Connection Setup Wizard to begin IPv6 Internet ConnectionIPv6 Internet Connection Setup Wizard Page IPv6 over PPPoE Static IPv6 Address Connection LengthPrefix IPv4 AddressIPv6 Manual Setup Auto DetectionStatic IPv6 Autoconfiguration PPPoE Configuration Start SettingsIPv6 in IPv4 Tunneling EndTo 4 Tunneling 6rd LifetimeLink-Local Connectivity Parental Controls Virtual Server Name IP Address Inbound Filter SchedulePort Forwarding TCP/UDPFirewall Application RulesName Trigger Manual Uplink Speed Enable Traffic ShapingQoS Engine Automatic Classification Dynamic FragmentationConfiguration Network Filters MAC Address Dhcp Client ClearAccess Control Access Control WizardPage Page Configure Website Select Allow or Deny Filter Below Website FiltersInbound Filters Action Select Allow or DenyFirewall Settings Application Level Gateway Configuration Routing Advanced Wireless Settings Automatic Wish Rules Wish SettingsEnable Wish PIN Settings Current PIN Reset PIN to Default Wi-Fi Protected Setup WPSEnable Add Wireless StationAdvanced Network Settings Guest Zone Between Zones zones createdIPv6 Firewall RangeIPv6 Routing Administrator Settings ServerTime Settings SysLog Email Settings NotificationReboot Device System SettingsLoad Settings from Local Hard Drive Update Firmware BrowseDdns Ddns for IPv6 HostsSystem Check Schedules General Wireless LANDevice Information Clear Email Now Save Log LogWhat to View View Levels Stats Active SessionsWireless IPv6 Support Wireless Security What is WPA?Wi-PnP Wireless Setup Page Wireless Connection Setup Wizard Wireless Connection Setup WizardPage Configure WPA-Personal PSK Configure WPA-Enterprise Radius Page Using Windows 7 and WPS for Wireless Configuration Security Double-click the DIR-827 router Page Connect to a Wireless Network Using WindowsPage Page Using Windows Vista Configure Wireless Security Page Using Windows XP Configure WPA-PSK Page Troubleshooting Why can’t I access the web-based configuration utility?What can I do if I forgot my password? Ping url -f -l MTU value Page Wireless Basics What is Wireless?Home Small Office and Home OfficeSecurity Centralize your router or Access PointEliminate Interference Wireless Modes Networking Basics Check your IP addressStep Step Highlight Internet Protocol TCP/IP and click PropertiesTechnical Specifications Contacting Technical Support Http//support.dlink.com Http//support.dlink.caWarranty Limited WarrantyNon-Applicability of Warranty Submitting a ClaimWhat Is Not Covered Limitation of Liability FCC Caution FCC Radiation Exposure StatementDéclaration d’exposition aux radiations Industry Canada StatementRadiation Exposure Statement Registration Register your product online at registration.dlink.com
Related manuals
Manual 1 pages 46.84 Kb
Top Page Image Contents