Craftsman 172.10721 Unpacking, Description, Parts List Fig, Know Your Buffer / Polisher

Page 6

UNPACKING

!WARNING: Your tool should NEVER be connected to the power

source when you are assembling parts, making adjustments, installing or removing bonnets, cleaning or when it is not in use. Disconnecting the tool will prevent accidental starting, which could cause serious personal injury.

1.Remove the buffer / polisher from the carton and inspect it carefully to make sure that no breakage or damage has occurred during shipping.

2.Do not discard any of the packing materials until all parts are accounted for.

3.Two bonnets are included: wax applicator bonnet for applying waxes, and a reusable terry cloth bonnet for removing waxes and polishing.

4.If any of the parts are damaged or missing (refer to PARTS LIST below), return the buffer / polisher to your nearest Sears store or Craftsman outlet to have the tool replaced.

!WARNING: If any parts are missing, DO NOT operate this

buffer / polisher until the missing parts are replaced. Failure to do so could result in possible serious personal injury.

PARTS LIST (Fig. 1)

Buffer / Polisher

Reusable Terry

Wax

Cloth Bonnet

Applicator

 

Bonnet

Operator’s Manual

10

 

DESCRIPTION

KNOW YOUR BUFFER / POLISHER

NOTE: Before attempting to use your buffer / polisher, familiarize yourself with all of the operating features and safety requirements.

Your Craftsman buffer / polisher has a precision-built electric motor and it should be connected to a 120-volt, 60-Hz AC ONLY power supply (normal household current). DO NOT operate on direct current (DC). The large voltage drop will cause a loss of power and the motor will overheat. If the tool does not operate when plugged into correct 120-volt, 60-Hz AC ONLY outlet, check the power supply. This buffer / polisher has a stub length, 2-wire power cord (no adapter needed).

This Craftsman Buffer / Polisher has the following features:

1.Powerful 1.0 Amp permanent magnet Motor with 3800 Orbits per Minute provides the power needed for quality waxing, buffing and polishing.

2.Precision tuned Counterweight system reduces vibration for smooth, comfortable operation with less operator fatigue

3.Precision tuned Counterweight System matched with Orbital Motion provides a “swirl-free” shine.

4.Ergonomically designed Perimeter Handle System provides maximum balance, control and gripping comfort on any horizontal or vertical surface.

5.Hook and Loop Strip helps keep extension cord securely plugged into buffer / polisher.

6.On / Off Slide Switch conveniently located for ease in control.

7.7-in. diameter Foam Pad follows surface contours for efficient buffing / polishing. Chemical resistant for long life.

8.One Wax Applicator Bonnet for applying wax.

9.One Reusable Terry Cloth Bonnet for removing wax and polishing.

10.Non-marring Flat Top of buffer / polisher provides a stable base when applying wax to bonnets and changing bonnets.

11.Permanently lubricated Ball Bearings for smooth, efficient operation.

12.Lightweight, High-impact Resistant Housing reduces weight, helps protect tool from damage.

11

Image 6
Contents Buffer / Polisher Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.ATable of Contents Safety SymbolsPersonal Safety Safety InstructionsWork Area Safety Tool USE and Care SafetyService Safety Electrical SafetySafety Symbols for Your Tool Safety Rules for Buffer / PolishersAdditional Rules for Safe Operation Safety Rules for Buffer / PolishersAlways wear eye protection when using this tool Do not USE Abrasive Compounds with this ToolDescription Parts List FigUnpacking Know Your Buffer / PolisherBefore YOU Begin to WAX, Buff and Polish Your CAR OperationKnow Your Buffer / Polisher Important do not Apply WAX Directly On CARAttaching the Polishing Bonnet to the Foam PAD Fig Running Your Buffer / Polisher and Waxing VehicleRunning Your Buffer / Polisher and Waxing Vehicle Important do not apply excessiveCAR Care Tips MaintenanceAccessories Never USE Abrasive Compounds with this Tool