Schumacher Connecting inverter cables, Inverter Connection, Connecting Your PSI-2000

Page 4

D.Connecting inverter cables

The inverter and the power source must be in the OFF mode.

Inverter Connection:

1.Locate the positive and negative plastic terminals located on the left side of the inverter. Using a flathead or standard screwdriver, unscrew the positive (red) and negative (black) terminal screws just enough to be able to insert the bare end of the connector cables.

2.Insert the bare end of the positive (red) cable into the positive terminal and bare end of the negative (black) cable into the negative terminal. Tighten each terminal screw so the cable cannot come loose.

Connecting inverter cables to 12V battery or 12V power source

1.Keep hands, hair, clothing and jewelry clear of battery terminals.

2.Wear protective eye (safety glasses) and clothing protection.

3.Connect the negative (black) inverter terminal cable to the power source or negative (-) battery terminal. Connect the positive (red) inverter terminal cable to the power source or positive (+) battery terminal. Make sure the connections are secure.

Note: Failure to make the correct con- nections will result in blown fuses and permanent damage to the inverter.

E.

Connecting Your PSI-2000

To Turn ON:

1.Push the rocker switch, located on the right side, to the “ON” (I) position. The LED indicator light should glow GREEN verifying the inverter is receiving power and can deliver power to your device. (A brief audio alarm may sound or red LED may flash. This is normal.)

2.Turn on the power source or device to be powered.

Note: If more than two devices are to be powered, start one device at a time to avoid a power surge and overloading the inverter. The surge load of each device should not exceed 2000 watts.

You can use an extension cord from the inverter to the device without sig- nificantly decreasing the power being generated by the inverter. For best operating results, the extension cord should be no longer than 50 feet.

To Turn OFF:

1.Push the rocker switch, located on the right side, to the “OFF” (O) position.

2.Turn off the power source and the device.

3.Disconnect inverter from power source and device.

4.Wait for the inverter to be cool to the touch before disconnecting it from the power source.

Note: The PSI-2000 inverter and device should always be unplugged when not in use.

Image 4
Contents Model PSI-2000 Before Using PSI-2000 Fastening the PSI-2000 to a flat surface Inverter FeaturesGrounding the PSI-2000 Connecting inverter cables Connecting Your PSI-2000Inverter Connection To Turn onUsing Gfci Outlet LeDs and Audio AlarmSafety Features Power SourceBlown Fuse How Do Power Inverters Work? IMPortant safety measuresTroubleshooting Problem Low or No Output Voltage Problem Red LED OnInverter is too hot thermal shut down mode Problem Audible Alarm On All The TimeSpecifications Limited WarrantyManuel d’utilisation Avant D’UTILISER L’ONDULEUR PSI-2000 Caractéristiques DE ’ONDULEUR Fixation DE L’ONDULEUR PSI-2000 À UNE Surface PlaneMise À LA Masse DE L’ONDULEUR PSI-2000 Raccordement DES Câbles DE L’ONDULEUR Raccordement DE ’ONDULEURBranchement DE Votre Onduleur PSI-2000 Pour L’OUVRIR Pour LE FermerUtilisation DE LA Prise À Disjoncteur DE Fuite À LA Terre Voyants ET Avertisseur SonoreFusible Sauté Source D’ALIMENTATIONFonctionnement DE ’ONDULEUR Mesures DE Sécurité ImportantesDépannage Spécifications Garantie LimitéeRemarques Manual de Instrucciones Antes DE Usar EL PSI-2000 Características DEL Inversor Para Fijar EL PSI-2000 a UNA Superficie PlanaPuesta a Tierra DEL PSI-2000 Conexión DE LOS Cables DEL Inversor Conexión DEL InversorPara Conectar SU PSI-2000 Para EncenderLEDs y Alarma Auditiva USO DEL Tomacorriente GfciUsar EL Inversor Para Operar UN TV O Dispositivo DE Audio Fusible QuemadoFuente DE Potencia Características DE Seguridad¿CÓMO Funcionan LOS Inversores DE POTENCIA? Medidas Importantes DE SeguridadSolución DE Problemas Especificaciones Garantía Limitada