Multiquip HPHA46411H, HPLA46411H manual HPLA/HPHA-SERIES 46TROWEL- Specifications Trowel, SideView

Page 13

HPLA/HPHA-SERIES 46"TROWEL— SPECIFICATIONS (TROWEL)

SideView

Figure 2. HPLA/HPHA-SERIES 46" Trowel Dimensions

Table 1. HPLA/HPHA-Series 46" Trowel Specifications

A– Height (Lifting Hook)

34.5 in (876.2 mm)

B– Height Engagement Lever)

41.1 in (1,044.2 mm)

C–Width

46.0 (1,168.4 mm)

D–Length

75.2 (1,910.1 mm)

Weight – Operating

230 lbs./105 Kg.

Sound Pressure

97 db

Vibration

2.5g (24.5 m/s2)

Ring Diameter

46 in (117 cm)

Number of Blades

3 or 4

Blade Tip Speed – FPM (m/s)

1,478 fpm (7.5 m/s)

Rotor – RPM (Gasoline)

60 to 125

Path Width – in. (cm)

48 (233)

NOTE:

1.Sound pressure is a weighted measure. Measured at the operators ear position while the walk-behind trowel is operating at full throttle on concrete in a manner most often experienced in “normal” circumstances. Sound pressure may vary depending upon the condition of the concrete. Hearing protection is always recommended.

2.The vibration level indicated is the maximum RMS (Root Mean Square) value obtained at the handle grip while operating the walk-behind trowel on curing concrete in a manner most often experienced in “normal” circumstances. Values were obtained from all three axes of motion. The values shown represent the maximum RMS value from these measurements.

HPLA/HPHA-SERIES 46" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (07/06/10) — PAGE 13

Image 13
Contents Models HPLA/HPHA-SERIES 46TROWEL- Proposition 65 Warning Page HPLA/HPHA-SERIES 46TROWEL-TABLE of Contents Best Deal! Order via Internet Dealers Only Parts Ordering ProceduresOrder via Fax Dealers Only Training Checklist HPLA/HPHA-SERIES 46TROWEL-TRAINING ChecklistMachine layout, location of components, checking of engine Daily PRE-OPERATION Checklist HPLA/HPHA-SERIES 46TROWEL- Daily PRE-OPERATION ChecklistDo not follow directions HPLA/HPHA-SERIES 46TROWEL- Safety Message Alerty SymbolsProperty, or the surrounding Always wear approved eye and hearing protectionYou do not follow instructions HPLA/HPHA-SERIES 46TROWEL- Rules for Safe Operation SafetyHPLA/HPHA-SERIES 46TROWEL- Rules for Safe Operation Maintenance SafetyEmergencies Always know the location of the nearest and first aid kitMachine Safety Decals HPLA/HPHA-SERIES 46TROWEL- Operation and Safety DecalsSideView HPLA/HPHA-SERIES 46TROWEL- Specifications TrowelHPLA/HPHA-SERIES 46TROWEL- Specifications Engines Specifications EngineHPLA/HPHA-SERIES 46TROWEL- General Information HPLA/HPHA-SERIES 46 Walk- Behind Trowels HPLA/HPHA-SERIES 46TROWEL- Controls and ComponentsEngine This trowel uses an 11HP Honda gasoline engine HPLA/HPHA-SERIES 46TROWEL- Controls and ComponentsInitial Servicing HPLA/HPHA-SERIES 46TROWEL- Basic EngineAssembly and Installation HPLA/HPHA-SERIES 46TROWEL Assembly and InstallationHandleTube Installation All Models Safety Stop SwitchWire Handle Height AdjustmentTighten cable clamp screw and swivel stop screw Slack from the cable Insert the cable end through the yoke eyelet FigureAgainst the yoke boss Before Starting HPLA/HPHA-SERIES 46TROWEL- PRE-INSPECTIONEngine Oil Check Controls HPLA/HPHA-SERIES 46TROWEL- PRE-INSPECTIONLifting theTrowel Onto a Slab Auxiliary Lifting Tube HPLA/HPHA-SERIES 46TROWEL Initial START-UPLifting Bail Option Starting the EngineHPLA/HPHA-SERIES 46TROWEL Initial START-UP Test the Safety Stop SwitchPlace the Choke Lever in the Closed position Pitchingthe Blades HPLA/HPHA-SERIES 46TROWEL OperationQuick Pitch Handle Maneuvering the TrowelHPLA/HPHA-SERIES 46TROWEL Operation Combo Blades Blades should be changed whenClip-On Float Blades Optional HPLA/HPHA-SERIES 46TROWEL Options Trowel Arm Adjustment ToolGrinding Attachments Engine Maintenance HPLA/HPHA-SERIES 46TROWEL Maintenance EngineEngineaircleaner HPLA/HPHA-SERIES 46TROWEL Maintenance EngineDaily WeeklyMaintenance Schedule HPLA/HPHA-SERIES 46TROWEL Maintenance TrowelSpider Removal HPLA/HPHA-SERIES 46TROWEL Maintenance TrowelTrowel Arm Removal Remove the trowel arm from the spider plateTrowel Arm Flatness Test Bronze Bushings Trowel Blade RemovalRe-Assembly Trowel Arm AdjustmentBelt Removal and Replacement TestingChanging a Blade Repeat steps 1- 5 for all remaining bladesTrowel Troubleshooting HPLA/HPHA-SERIES 46TROWEL Troubleshooting TrowelTrowel Troubleshooting HPLA/HPHA-SERIES 46TROWEL Troubleshooting TrowelDifficult to start HPLA/HPHA-SERIES 46TROWEL Troubleshooting EngineXxxxx only Not Used on HPLA/HPHA-SERIES 46TROWEL Explanation of CodesDescription HPLA/HPHA-SERIES 46TROWEL Suggested Spare PartsARM 16-1/2 Nameplates and Decals HPLA/HPHA-SERIES 46TROWEL Nameplate and DecalsDecal Power Trowel Decal PRE-LOAD IndicatorNameplate and Decals Decal QUICK-PITCH HandleStandard Handle Assy Detail a See Detail B HPLA/HPHA-SERIES 46TROWEL Standard Handle AssyHPLA/HPHA-SERIES 46TROWEL Standard Handle Assy HPLA/HPHA-SERIES 46TROWEL QUICK-PITCH Handle Assy Wire ASSY., Safety Stop Switch CONNECTOR, QP Control ARMBLOCK, QP Adjustment DECAL, Preload Trim IndicatorHPLA/HPHA-SERIES 46TROWEL Quick Pitch Handle Assy HOUSING, Throttle Cable SCREW, QP Trim AdjustmentQuick Pitch Handle Assy DECAL, ArrowBlade Spider Assy HPLA/HPHA-SERIES 46TROWEL 4-BLADE Spider AssyWear Ring AssyFlange Bearing Wear PlateGearbox & Engine Mounts Assy HPLA/HPHA-SERIES 46TROWEL Gearbox & Engine Mounts AssyFLANGE, Input Shaft SEAL, OIL National #470954RING, O -139 Buna N SHIM, Input 0.002 ThickHPLA/HPHA-SERIES 46TROWEL Gearbox & Engine Mounts Assy PIN, Yoke ARM, YokeStationary Guard Ring BUSHING, Guard RingEngine Assy HPLA/HPHA-SERIES 46TROWEL Engine AssyPart Name QTY Remarks Guard Ring Assy HPLA/HPHA-SERIES 46TROWEL Guard Ring Assy1940 20811Detail a HPLA/HPHA-SERIES 46TROWEL Stabilizer Ring Assy1237 WASHER, LOCK, 5/16 MEDBlades & ARM ADJ. Fixture Assy HPLA/HPHA-SERIES 46TROWEL Blades & ARM ADJ. FixtureHPLA/HPHA-SERIES 46TROWEL Blades & ARM ADJ. Fixture Lifting Bail ASSY. Option HPLA/HPHA-SERIES 46TROWEL Lifting Bail ASSY. Option10229 Hhcs 5/16-24X1 0161C HPLA/HPHA-SERIES 46TROWEL Lifting Bail ASSY. Option0205 Hhcs 3/8-16X1 1394 Fhscs 3/8-16X1 0166A AIR Cleaner Assy Honda GX-340K1QAP2 Engine AIR Cleaner AssyGROMMET, AIR Cleaner COVER, AIR CleanerCOLLAR, AIR Cleaner Collar B, AIR CleanerCamshaft Assy Honda GX-340K1QAP2 Engine Camshaft AssyROD, Push SPRING, Weight ReturnARM, Valve Rocker LIFTER, ValveCarburetor Assy Honda GX-340K1QAP2 Engine Carburetor AssyGasket SET PLATE, Lever SettingValve SET, Float Float SETCrankcase Cover Assy Honda GX-340K1QAP2 Engine Crankcase Cover AssyHOLDER, Governor Weight WEIGHT, GovernorPIN, Governor Weight GASKET, Case CoverControl Assy Honda GX-340K1QAP2 Engine Control AssyHOLDER, Wire SPRING, Control AdjustingARM, Governor ROD, GovernorCylinder Barrel Honda GX-340K1QAP2 Engine Cylinder Barrel AssySHAFT, Governor ARM Switch Assembly OIL LevelBOLT, Drain Plug NUT, Flange 10MMCylinder Head Assy Honda GX-340K1QAP2 Engine Cylinder Head AssyCLIP, Valve Guide GUIDE, Valve OS OptionalGASKET, Cylinder Head COVER, HeadCrankshaft Assy Honda GX-340K1QAP2 Engine Crankshaft AssyWEIGHT, Balancer FAN Cover Assy Honda GX-340K1QAP2 Engine FAN Cover AssyCLIP, Tube CLIP, Wire HarnessCOVER, FAN *NH1* Black ShroudFlywheel Assy Honda GX-340K1QAP2 Engine Flywheel AssyFlywheel FAN, CoolingNUT, Special 16MM Fuel Tank Assy Honda GX-340K1QAP2 Engine Fueltank AssyJoint Fuel Tank RUBBER, Supporter 107MMTANK, Fuel NH1 Black GASKET, Fuel Filler CAPIgnition Coil Assy Honda GX-340K1QAP2 Engine Ignition Coil AssyWIRE, Stop Switch 430MM GROMMET, WireCoil ASSEMBYL, Ignition Muffler Assy Honda GX-340K1QAP2 Engine Muffler AssyPROTECTOR, Muffler MufflerPROTECTOR, Exhaust Pipe PIPE, ExhaustPiston Assy Honda GX-340K1QAP2 Engine Piston AssyRing SET, Piston Standard BOLT, Connecting RODRing SET, Piston OS Ring SET, PistonRecoil Starter Assy Honda GX-340K1QAP2 Engine Recoil Starter AssyPULLEY, Recoil Starter BlackRATCHET, Starter SPRING, FrictionLabels Assy Honda GX-340K1QAP2 Engine Labels AssyLABEL, Caution EmblemMARK, Choke External MARK, OIL Alert ETerms and Conditions of Sale Parts Page HERE’S HOW to GET Help