Warranty, Operation | Hitachi 75 instruction

HITACHI SuperDrive Auto-feed Screw System

WARRANTY

HITACHI SuperDrive tools and system components are warranted to the original purchaser at retail to be free from defects in material and workmanship one year from the date of purchase.

The warranty shall only cover defects and not normal wear and tear, which occurs with use.

HITACHI SuperDrive assumes no responsibility whatsoever for malfunctions, failures or defects resulting from misuse, abuse, neglect, alteration or modification. SuperDrive makes no warranty and shall not be liable as to the fitness of its tools or fasteners for any particular uses or applications. No other warranties, representations or promises as to the quality or performance of the SuperDrive fastening tool other than those contained herein are made.

ANY IMPLIED WARRANTY GRANTED UNDER STATE LAW, INCLUDING WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO DURATION TO THE EXPRESS WARRANTY GRANTED HEREUNDER. SUPER- DRIVE IN NO EVENT SHALL BE LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, SO THE

ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.

Operating Instructions

For SuperDrive 75 Series

OPERATION

1. Check Driver Bit to make sure it is in good con-

dition.

• If it is broken or worn out, install a new one.

2. IMPORTANT! Make sure the forward-reverse

switch is in the forward position.

3. Insert a strip of screws into the feed track. Pull

it through and insert the front into the index mod-

725413

725470	725471

PARTS LIST - 75 SERIES TOOL		QTY
725414	MODULE (GREEN DOT)	1
725415	SPRING (GREEN) 1.7mm	1
725413	NOSEPIECE FLAT HEAD SCREW
	M4x10mm	1
725470	NOSEPIECE SUBFLOOR AND
	METAL-TO-METAL	1

ule until the first screw is in driving position in the

center of the nose piece. See Figure 1.

725414 (GREEN DOT)

725475

725472 725473

725416

725474

725424

725416725422

725425

725432

725415 (GREEN)

725471	NOSEPIECE DECK/DRYWALL	1
725425	END PLATE FOR 75	1
725424	WING SCREW FOR END PLATE	1
725423	BODY HEX SOCKET CAP SCREW
	M4x8	1
725422	BODY HEX SOCKET CAP SCREW
	M4x10	2
725416	RETAINER SCREW - M3x6	2
725416	RETAINER FOR MODULE 3mm	2
725427	BRACKET FOR FEEDTRACK	2
725428	FEED TRACK HEX SOCKET SCREW
	1/4”-20 x 7.4mm	5
725426	FEED TRACK	1
725432	TUBE FOR END PLATE	1

DEPTH ADJUSTMENT PARTS		QTY
725472	DEPTH CONTROL RETAINER	1
725474	DEPTH CONTROL SPRING	1
725473	DEPTH CONTROL ADJUSTMENT

FIGURE 2.

725428

725427

	WHEEL	1
725475	SNAP E RING E2	1

725423	725426	EXTENSION PARTS		QTY
725423	725426	725476	EXTENSION 19”	1
		725476	EXTENSION 19”	1
		729430	BIT EXTENSION	1
		729431	HANDLE ASSEMBLY	1

725430

725431

725476

Call 1-800-706-7337 or your sales rep. for replacement parts.

Appx. 1/4”

FIGURE 1.

4.Adjust the nosepiece so there is a 1/8” to 1/4” gap between nose piece and tip of screw.

•Tighten the nosepiece screw securely. See Figure 2.

5.Follow instructions on the sticker. Push slider in to adjust. Then turn knob until it locks.

FIGURE 3.

6.Turn on the motor before starting to drive screws.

•The motor can be locked to the ON position.