Multiquip SP706020, SP706036, SP706030, SP706026, SP706012 manual Control Panel Decals

Page 10

CONTROL PANEL DECALS

1

2

ENGINE

Air filter: Replace outer element when the SYSTEMS STATUS air filter restriction light comes on. Replace inner element every fourth outer element.

Oil: Check oil level daily, do not overfill.

Oil type: See Engine Manual.

Oil Service: Change oil and filter every 125 hours of operation.

Fuel Filter: Change fuel filter every 250 hours of operation.

THROTTLE

PUSH OR PULL KNOB.

 

HYDRAULIC SYSTEM

MAINTENANCE INSTRUCTIONS

 

 

LUBRICATION

 

DRIVE BELTS

 

 

 

 

 

 

 

 

 

 

Service:

 

 

 

 

 

 

Belt Tension:

 

 

 

 

Oil Level:

Check reservoir daily. Fill reservoir to

 

 

 

 

 

 

Grease every 125 hrs. of operation.

 

 

 

 

 

 

 

line marked FULL COLD.

 

 

 

 

 

 

 

 

Type:

 

 

 

 

 

 

bladeshaft drive is engaged.

 

 

 

Oil type:

15W-40 premium grade engine oil.

 

 

 

Note:

 

 

 

 

 

 

 

 

To Adjust

Perform following procedure with saw fully lowered.

 

 

Oil Service:

Change oil and filter every 500 hours of

 

 

 

Locations:

 

 

 

 

 

Drive Belt

 

 

 

 

 

 

 

 

Wheel drive propulsion system, lift pump,

 

 

 

 

Tension:

 

 

 

 

 

operation or annually, whichever occurs first.

 

and oil bath bladeshaft share common

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Reservoir

Reservoir is located inside console. Remove

 

hydraulic oil reservoir, thus are maintained

 

 

pin (1).

 

 

 

 

 

 

 

 

Location:

rear panel for access.

 

as a single system.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AUXILIARY

LIGHTS

BLADESHAFT

IGNITION SWITCH

BLADE SPEED

TACHOMETER

ENGINE WILL NOT CRANK

 

 

OR START WHEN E-STOP

ON

ON

DIS-ENGAGE

 

ENGINE PRE-HEAT

 

BUTTON IS DEPRESSED

 

 

 

 

GLOW PLUG

 

 

 

 

 

START

 

 

 

 

 

 

ON

 

 

 

 

 

 

ENGINE

 

 

 

OFF

OFF

ENGAGE

PRE-HEAT

 

 

 

OFF

SYSTEMS STATUS

 

 

 

 

 

 

 

 

3

DEPTH STOP CONTROL

To Control Depth of Cut with Saw

Running and Blade Mounted:

Step 1: Raise saw above desired cutting depth.

Step 2: Turn depth control knob counterclockwise until saw cannot be lowered by pushing raise/lower switch forward.

Step 3: Hold raise/lower switch in the lowering position and rotate the depth control knob clockwise until desired cutting depth is achieved. The saw will repeat to the same depth until re-adjusted.

To Re-adjust for Full Cutting Depth:

Hold raise/lower switch in the lowering position and rotate the depth control knob clockwise until saw is fully lowered. Rotate depth control knob clockwise additional 1 turn.

WATER

FLOW

CONTROL

ADJUST WATER FLOW VALVE

FOR DESIRED WATER FLOW

DEPTH

 

INDICATOR

 

 

5

6

7

 

 

 

 

 

BLADESHAFT ROTATION DIS-ENGAGEMENT SYSTEM

 

150

175

8

 

 

4

125

 

200

 

 

100

 

 

230 9

 

FORWARD

 

 

 

 

 

To stop bladeshaft rotation:

3

 

 

 

 

 

 

 

 

255

10

 

75

 

 

 

 

 

 

 

280

 

To start bladeshaft rotation:

2

 

 

 

11

 

50

305

12WARNING

 

 

 

 

330

 

1

25

 

 

 

13

 

 

 

355

 

 

 

380

14

 

 

 

0

 

 

 

 

0

MM

15

 

 

 

 

INCH

NEUTRAL

TO ADJUST CUT DEPTH INDICATOR:

LOWER SAW UNTIL BLADE CONTACTS

SURFACE, ADJUST DIAL TO ZERO.

RAISE/LOWER

SWITCH

REVERSE

NEVER EXCEED BLADE MANUFACTURER'S RECOMMENDED RPM'S

FWD-NEUTRAL-REV

 

CONTROL

OPERATING INSTRUCTIONS

BEFORE

STARTING:

WATER

SUPPLY:

BLADES:

STARTING

ENGINE:

STOPPING

ENGINE:

FWD-

NEUTRAL-

REV

CONTROL:

RAISE-

LOWER

FUNCTION:

BRAKES:

.

WATER PUMP

ON

OFF

ON

WATER

OFF

PAGE 10 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Models Proposition 65 Warning SILICOSIS/RESPIRATORY Warnings Silicosis Warning SP7060 StreetPro Series Parts Ordering Procedures Explanation of code in remarks column Xxxxx only Not Used onSuggested Spare Parts Nameplates and Decals DECAL, Stay Level Handle White Safety ItemDECAL, Attention Battery Disconnected DECAL, MQ Multiquip 5.93 XControl Panel Decals DECAL, MAINTENANCE, 7000 Series Part NameElectrical Control Assy CONNECTOR, 4-WAY Socket INDICATOR, EngineSWITCH, Roller ARM BOOT, Toggle SwitchConsole Mounts Assy MOUNT, Isolator Front ISOLATOR, RB2 RING/BUSHINGRubber ISOLATOR, TPC# MOUNT, Isolator SideRear Console Access Panel Assy Document BOX PANEL, Rear SAW AccessLATCH, Rear SAW Access Panel STRIP, Vertical SAW ConsoleLight CONNECTOR/DASH Access Assy WASHER, Lock 5/16 MED Connector PLUG, 4-PIN FemaleWASHER, Flat SAE 5/16 GRD 9YZ KNOB, Comfort Grip StarBelt and Engine Guards Assy WASHER, Flat SAE 3/8 GRD 9 YZ Depth INDICATOR/STOP Switch ASSY. old style KNOB, SAW Depth Indicator BASE, SAW Depth IndicatorSHAFT, Depth Indicator PULLEY, Cable .75 ODDepth INDICATOR/STOP Switch ASSY. new style BRACKET, Cable Indicator BELT, Indicator DriveHOUSING, Depth Indicator BUSHING, FlangedR Assy GROMMET, 1/2 ID PLATE, FNR Access CoverBEARING, Roller # 6204 2RS SPACER, FNR PivotFuel Assy Fuel Tank CLAMP, Hose Worm #CLAMP, Loop Cushioned #8 TUBING, Vinyl 1/4 ClearBattery Assy QTY STAY-LEVEL Handlebars Assy PIN, SLH Coupler Pivot WASHER, Flat SAE 1/2 GRD 9 YZGRIP, Handlebar Handlebar Boot Assy PLATE, Retainer Water System Assy Hose ASSEMBLY, Crossover Engine Assy WASHER, Flat SAE 1/4 GR 9 YZ WASHER, Flat SAE 5/16 GRD 9 YZThrottle Lever Throttle control assy SWIVEL, Cable END W/ Washer ThrottleLEVER, Throttle WASHER, M6Engine mounts assy WASHER, Flat SAE 9/16 GRD 9 YZ WASHER, Flat SAE 7/16 GRD 9 YZAir cleaner assy Hose ASSY, AIR Intake INDICATOR, Electrical ServiceSafety FILTER, Deutz BF3L2014 TUBE, AIR Intake BreatherMuffler assy WASHER, M8 EXHAUST, 12 ExtensionWASHER, M10 X 21MM Zinc GASKET, Turbo Inlet DeutzLift bail assy 37114 Platform guards/rear pointer assy SHIELD, Concrete Slurry STRAP, Lower Belt GuardPOINTER, Rear SAW GUARD, SAW Blade CollarWheel drive assy Brake PAD MOUNT, Wheel MotorWHEEL, 12 X 3 Tapered Bore Brake ARMFront axle assy FITTING, Grease Zerk STR 1/4 Front Axle W/AWASHER, Flat 5/8 SAE GRD9 YZ CAP, Grease Zerk #2 YellowHydraulic system assy Filter HEAD, Transaxle Lift Cylinder AssemblyFILTER, Transaxle CYLINDER, Brake 2 X 1.5 StrokeEngine pivot cylinder assy PISTON, Pilot VALVE, CheckSolenoid Coil 12VDC CYLINDER, HydraulicHydraulic hoses assy Hose ASSEMBLY, #6-8 LP Hose ASSEMBLY, #4 LPHose ASSEMBLY, #4 HP Parflex Hose ASSEMBLY, #6 LPHydraulic fittings and clamps assy FITTING, STR 4MJ 4MO Clamp ASSEMBLY, HoseClamp ASSEMBLY, 5/16 Hose FITTING, 90 4MJ 4MOFront pointer assy WHEEL, Pointer 6 X PointerBUSHING, Flange 1.0 OD X .75 ID AXLE, Pointer WheelBelt drive assy SPACER, Belt Tensioner BELT, 5G 3 VX 530 PowerbandPLATE, Engine ADAPTER-DEUTZ SHAFT, Engine DRIVE-DEUTZ BELT, AX-3568 SP7060 Series Multiquip SAW Parts Manual REV. #5 05/06/11 FAN, CW 8 10 Blade Blade Shaft AssyRING, FAN Mount SHOE, Upper BeltsideDrive pulley assy SUPPORT, Engine Drive Bearing SPRING, Smalley Wavo RW-0162Bladeshaft assy Washer Flat SAE 7/16 GRD 9 YZ HOUSING, BladeshaftBLADESHAFT, 7000 Series Drain PLUG, Magnetic 1/216, 20, 26 bladeguard assy Bladeguard W/A, 26 Rear Half Bladeguard W/A, 16 Rear HalfBladeguard W/A, 20 Rear Half Bladeguard W/A, 16 Front Half30, 36 bladeguard assy Bladeguard W/A, 36 Rear Half Bladeguard W/A, 30 Rear HalfBladeguard W/A, 36 Front Half Optional weight kit assy 37829 Weight kit Terms and conditions of sale parts SP7060 Series Multiquip SAW Parts Manual REV. #5 05/06/11- HERE’S HOW to GET Help
Related manuals
Manual 64 pages 49.48 Kb

SP706012, SP706026, SP706030, SP706036, SP706020 specifications

Multiquip is a prominent name in the construction equipment industry, known for its innovative and reliable products. Among its versatile offerings, the Multiquip SP706020, SP706016, SP706036, SP706030, and SP706026 stand out as notable concrete pump models. These pumps provide exceptional performance and efficiency, making them ideal for a wide range of applications.

Each model in this lineup is engineered for maximum durability and reliability. The SP706020, for instance, features a powerful and efficient hydraulic system that allows for smooth operation and consistent performance, even in demanding conditions. It is designed with a robust frame that can withstand rigorous job site environments, ensuring longevity and reduced maintenance.

The SP706016 stands out with its compact design, making it suitable for smaller job sites while still offering high output and efficiency. This model is equipped with advanced safety features, such as emergency stop buttons and pressure relief valves, ensuring safe operation for the user and surrounding personnel.

Notably, the SP706036 is designed for high-capacity pumping. It is ideal for larger projects that require higher output without compromising on efficiency. Its advanced pumping technology reduces the potential for blockages, enhancing overall productivity. The SP706030 presents a balance between power and size, making it an excellent choice for medium-scale projects.

The SP706026 is notable for its energy-efficient design, which minimizes fuel consumption while providing robust performance. This model reflects Multiquip's commitment to sustainability and cost-effectiveness, allowing contractors to save on operational costs over time.

Across the series, user-friendly controls and adjustable settings provide operators with the flexibility needed to handle various types of concrete mixes and job specifications. Additionally, these models are fitted with high-quality components that enhance performance and reduce wear and tear.

In summary, the Multiquip SP706020, SP706016, SP706036, SP706030, and SP706026 are versatile concrete pumps equipped with cutting-edge technology, ensuring high efficiency, reliability, and safety on any job site. Their various features and specifications make them a valuable addition to any construction operation, catering to diverse project needs while ensuring exceptional performance.
Top Page Image Contents