Craftsman 172.67098 operating instructions Forward, Installing the Battery

Page 27

OPERATION cont.

CHARGING THE BATTERY PACK cont. (Fig. 5 and 5a)

8.The battery pack will become slightly warm to the touch while charging. This is normal and does not indicate a problem.

9.Do not place the battery charging stand / transformer in an area of extreme heat or cold. It will work best at normal room temperature.

10.When battery pack becomes fully charged, unplug battery charging stand / transformer from power supply and remove the battery pack.

CHARGING A HOT BATTERY PACK

When using your tool continuously, the batteries in your battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge.

NOTE: A hot battery pack only occurs when prolonged continuous use of your drill/driver causes the batteries to become hot. It should not occur with typical use.

OPERATION cont.

TRIGGER SWITCH (Fig. 7 and 7a)

To turn the drill ON, push the Forward / Reverse Selector Switch with Power Lock-Off to the FORWARD or REVERSE location (see arrow direction embossed on switch), and depress the trigger switch. To turn the drill OFF, release the trigger switch.

Fig. 7

 

Fig. 7a

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FORWARD

REVERSE

INSTALLING THE BATTERY

 

Fig. 6

PACK IN DRILL / DRIVER (Fig. 6)

 

1. Place the Forward / Reverse Selector Switch

 

with Power Lock-Offinto the center position to

 

lock the power off.

 

2. Place the battery pack in the drill, aligning the

 

raised rib on battery pack with groove inside

 

the drill.

 

3. Make sure the latches on each side of the

 

battery pack “snap” into place, and the battery

 

pack is secured in the drill / driver before

 

beginning operation.

 

VARIABLE SPEED (Fig. 8)

The variable speed trigger switch delivers

higher speed and torque with increased pressure on the trigger switch and lower speed and torque with decreased pressure on the trigger switch.

NOTE: You might hear a whistling or ringing noise from the trigger switch when operating at low speeds. Do not be concerned; this is a normal part of the switch function.

7

5

3

1

Fig. 8

!CAUTION: When placing battery pack in the tool, be sure raised rib on battery pack aligns with the bottom of the drill and latches into place properly. Improper installation of the battery pack can cause damage to internal components.

!WARNING: Cordless Battery Tools are always in operating condition when the battery pack is installed in the tool. Therefore the Forward / Reverse Selector Switch with Power Lock-Off should always be in the center position, locking the power off, when the tool is not in use or when you are carrying it at your side.

16

17

Image 27
Contents Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A Warranty Safety Unpacking Description Operation MaintenanceSafety Symbols Table of ContentsPersonal Safety Safety InstructionsSafety Instructions Work Area SafetyService Safety Electrical SafetyBattery Pack Safety Symbols for Your ToolSafety Rules for Battery Charging STAND/ Transformer Additional Rules for Safe Operation Safety Rules for Battery Charging STAND/ TransformerUnpacking Parts List FigGlossary of Terms for Woodworking Glossary of Terms for WoodworkingDescription DescriptionKnow Your Cordless Circular SAW Fig Blade Guard System Fig OperationOperation SAW BladesCharging the Battery Pack and 8a Removing Battery Pack fromCircular SAW Fig Charging a HOT Battery Pack Installing the Battery PackTrigger Switch with Power Making Cross Cuts and RIP Cuts Fig Starting a CUT FigTo Help Maintain Control To Help Maintain ControlMaking Bevel Cuts Figs Using a Straight Edge FigHOW to SET Your Bevel Angle Fig Installing and Using Edge Guide sold separately FigBUILT-IN Sawdust Ejection Chute and 20a MaintenanceRoutine Maintenance Making Pocket Cuts FigBatteries MaintenanceChanging the Blade Figs and 21a LubricationBattery Pack Removal and Preparation for Recycling TroubleshootingAccessories Parts ListParts List Get it fixed, at your home or ours Description WarrantySafety MaintenanceRead ALL Instructions Safety Instructions Indicates danger, warning or caution Specific Safety Rules for Cordless Drill / DriversSpecific Safety Rules for Cordless Drill / Drivers Safety Rules for Battery Charging Stand / TransformerSafety Rules for Battery Charging Stand / Transformer Carton Contents This Cordless Drill / Driver has the following features Know Your Cordless Drill / Driver FigDrill No , in Kit Place the Forward / Reverse Selector Switch Power LOCK-OFFCharging the Battery Pack and 5a Remove Battery Pack fromForward Installing the BatteryDecrease 10a Increase Plus 1 Adjustable Torque Clutch , 10a and 10bElectric Brake Keyless Chuck and 9aWrong Operation AS a Screwdriver Fig Operation AS a Drill FigGeneral Maintenance To Retighten a Loose Chuck Figs and 18aChuck Removal Figs , 17a and 17b Cordless Drill / Driver AccessoriesModel No .64120 18.0 Volt Kit IN. Variable Speed / Reversible Cordless Drill / Driver