Warning! The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used. The vibration level may increase above the level stated.
When assessing vibration exposure to determine safety measures required by 2002/44/EC to protect persons regularly using power tools in employment, an estimation of vibration exposure should consider, the actual conditions of use and the way the tool is used, including taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time.
Labels on tool
:The following pictograms are shown on the tool:
#This tool is double insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate.Electrical safety
uIf the supply cord is damaged, it must be replaced by the manufacturer or an authorised Black & Decker Service Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features:
1.On/off switch
2.
3.Dust extraction outlet
4.Shoe plate
5.Saw blade support roller
Fig. E
6. Saw blade storage compartment (KS602E & KS603E)
Assembly
Warning! Before attempting any of the following operations, make sure that the tool is switched off and unplugged and that the saw blade has stopped. Used saw blades may be hot.
Adjusting the saw blade support roller (fig. A & B)
uLoosen the two screws (8).
uPush the blade support roller (5) forward until it touches the back edge of the saw blade (7).
uTighten the two screws (8).
Fitting and removing the saw blade (fig. C)
uBefore fitting or removing the saw blade (7) the saw blade support roller (5) must be adjusted to the rear position so that it does not contact the blade.
uLoosen (do not remove) the two screws (10).
uHold the saw blade (7) with the teeth facing forward.
uInsert the shank of the saw blade (7) into the blade holder
(9) as far as it will go.
uSlightly tighten the two screws (10) alternately to position the blade, then fully tighten the two screws (10).
uAdjust the saw blade support roller (5) as described above.
uTo remove the saw blade (7), turn both screws (10) one turn
Connecting a vacuum cleaner to the tool (fig. D)
An adaptor (11) is required to connect a vacuum cleaner or dust extractor to the tool. The adaptor can be purchased from your local Black & Decker retailer.
uPush the adaptor (11) into the dust extraction outlet (3).
uConnect the vacuum cleaner hose (12) to the adaptor (11).
Saw blade storage (KS602E & KS603E only) (fig. E)
Saw blades (7) can be stored in the storage compartment (6) located on the side of the tool
uOpen the cover of the saw blade storage compartment (6) by holding the tab on the top of the door and pulling outwards.
uRemove or store saw blades (7) in the storage compartment (6).
uClose the cover of the saw blade storage compartment (6) and make sure that it is latched closed.
Cut line blower (fig. F)
uTo aid visibility when cutting, your jigsaw is equipped with a cut line blower (13) which will keep the work area clear of dust as you saw.
Use
Adjusting the shoe plate for bevel cuts (fig. G)
The shoe plate can be set to make either a straight cut or a left or right bevel cut at an angle of 45°.
uLoosen the screws (8).
uPull the shoe plate (4) forward, rotate the shoe plate (4) to the left or right and push it back into the 45° location.
uPush the blade support roller (5) forward until it touches the saw blade (7).
uTighten the screws (8).
To reset the shoe plate for straight cuts:
uLoosen the screws (8).
uPull the shoe plate (4) forward, rotate to the centre and push it back into the 0° location.
uPush the blade support roller (5) forward until it touches the saw blade (7).
7