Craftsman 315.1152 manual Charging Battery Pack, See, Information for Recharging HOT BAT Tery Pack

Page 10

_1 WARNING: Do not allow familiarity with this tool to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe

injury.

CHARGING BATTERY PACK

See Figure 1, Page 9

The battery pack for this tool has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge it at least 3 hours prior to use.

Note: Batteries will not reach full charge the first time they are charged. Allow several cycles (drilling followed by recharging) for them to become fully charged.

TO CHARGE

•Charge battery pack only with the charger and charging stand provided.

•Make sure power supply is normal house voltage, 120 volts, 60 Hz, AC only,

•Connect charger to power supply.

•Place battery pack in charging stand. Align raised rib on battery pack with groove in charging stand. See

Figure 1,

•Press down on battery pack to be sure contacts on

battery pack engage properly with contacts in charging stand.

•When properly connected, the red light on charging stand will turn on.

•Note: if charger does not charge battery pack, return battery pack, charging stand, and charger to your nearest Sears Repair Center for electrical check.

•After normal usage, 3 hours of charging time is required to be fully charged. A minimum charge time of 3 hours is required to recharge a completely discharged tool

•The battery pack will become slightly warm to the touch while charging. This is normal and does not indicate a problem.

•Do not place charger in an area of extreme heat or

cold. It will work best at temperatures between 5O°F_ 100°E

•When batteries become fully charged, unplug charger from power supply and remove the battery pack.

INFORMATION FOR RECHARGING HOT BAT-

TERY PACK

When using this tool continuously, the batteries in your battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before at- tempting to recharge.

Note: This situation only occurs when continuous use of your drill causes the batteries to become hot. It does not occur under normal circumstances. Refer to "CHARGING BATTERY PACK" for normal recharging of batteries. If the charger does not charge your battery pack under normal circumstances, return both the battery pack and charger to your nearest Sears Repair Center for electrical check.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 0Qs Sears, Roebuck and Co,, Dept, 817WA, Hoffman Estates, IL Work Area Electrical SafetyPersonal Safety Tooluseand CareDo not charge battery tool in a damp or wet loca ServiceAdditional Rules for Safe Operation Result in serious personal injury Symbol Name DESIGNATION/EXPLANATION PowerService Symbol Signal MeaningSwitch Lock Product Specifications DRILL-DRIVERSwitch Know this ToolInstructions Battery Charging Stand REDCharger Packing ListSee , Charging Battery PackInformation for Recharging HOT BAT Tery Pack Batterypack Latches Depresslatchesto Releasebatterypack To Install Battery PackTo Remove Battery Pack Unlock Selectorwithreverse Centerlockposition ForwardReversible DrillbitAdjusting Adjustable Torque ClutchTo Adjust Torque Unlock Drillbit Release Chuckcollar ChuckjawsScrewdriverbits BIT Storagearea Drilling Mallet Chuck RemovalSee Figures 11, 12, Chuckjaws HexkeykeylessBattery Pack Removal and Preparation for Recycling BatteriesPage Key Number Description Qty See Back page for Parts Ordering InstructionsCan Be Purchased Thru Rsos Retail Special Order System Parts List

315.11521, 315.1152 specifications

The Craftsman 315.1152 and 315.11521 are two versatile power tools designed for a variety of applications, making them perfect additions to any home workshop. Known for their reliability and performance, these tools leverage advanced technologies that enhance user experience and efficiency.

One of the main features of the Craftsman 315.1152 is its powerful motor. This high-performance motor ensures high torque output, allowing users to tackle even the most demanding tasks. Whether you're drilling into hardwood or driving screws into tough materials, this tool remains consistent and efficient, minimizing the effort required.

The Craftsman 315.11521, on the other hand, boasts a compact design that enables easy handling and maneuvering in confined spaces. Despite its smaller profile, it does not compromise on power, making it an excellent choice for users who need portability without sacrificing performance.

Both tools come equipped with variable speed settings, providing users with optimal control for different applications. The adjustable speed mechanism allows for precision work, whether you're performing delicate tasks or need to apply more power for heavy-duty jobs.

A standout characteristic is the ergonomic design of the grips on both models. This design reduces fatigue during prolonged use, making them comfortable to hold. Furthermore, the lightweight construction of the tools enhances usability, ensuring that even extended projects can be completed with ease.

Safety features are also integral to the design of the Craftsman 315.1152 and 315.11521. Each tool is fitted with a reliable safety lock mechanism that prevents accidental activation, providing peace of mind especially in busy workshops.

Moreover, these Craftsman tools are compatible with a range of accessories and attachments, allowing for expanded functionality. Whether you need drill bits, sanding discs, or other attachments, these tools can be adapted for various tasks, making them highly versatile.

Craftsman stands behind the quality of their products, offering warranties that reflect their commitment to durability and customer satisfaction. Overall, the Craftsman 315.1152 and 315.11521 are exceptional tools designed to make household projects and professional jobs more manageable, ensuring that users can work smarter and more efficiently.
Top Page Image Contents