PC Gaming, Start Here | ButtKicker BK-GR2 specification

PC GAMING

START HERE

Position the strain relief rubber band on the ButtKicker Gamer cable

1.Position the rubber strain relief on the ButtKicker® Gamer cable until it is approx. 6” away from the ButtKicker Gamer.

2.Pull the loop of the strain relief nearest to the ButtKicker Gamer tight.

3.Place the second loop about 8” further down the cable and pull it tight. (refer to figure 1)

Attach the ButtKicker Gamer to your center post chair

1.Raise the pneumatic lift on your chair (make the seat of the chair higher). Then, push down the sleeve covering the center post to expose the post. (refer to figure 2)

2.Loosen the knob on the arm of the ButtKicker Gamer and place the clamp around the post.

3.Tighten the knob and secure the ButtKicker Gamer in place on the chair seat. (refer to figure 2)

4.Use the supplied Velcro® cable wraps to tie the end of the ButtKicker Gamer cable to one leg of your seat. (refer to figure 3)

Position the ButtKicker Power Amplifier and connect to the ButtKicker Gamer

Do not turn on the amplifier until all

of the connections are made!

1.Connect the long quick release cable to the short cable coming from the ButtKicker Gamer. (refer to large diagram & figure 3b) [Note that the cables may be disconnected using the quick release connector at any time if desired. HOWEVER, make sure the amplifier is turned OFF BEFORE disconnecting the cables.]

2.Connect the long quick release cable to the banana jacks on the back of the ButtKicker Power Amplifier. (+) connects to the red terminal, (-) connects to the black terminal.

3.Position the amplifier near the audio source (PC), and accessible to the user.

4.If desired, use the optional base stand to position the amplifier in an upright, verticle position.

5.Connect the power cord to the power terminal on the back of the ButtKicker Power Amplifier and then plug it into a power outlet.

Connecting the Audio Signal from

the PC to the ButtKicker Power Amplifier

For a stereo or 4 channel sound card, insert the mini “Y” adaptor into the “line out” (usually a green jack). Connect the mini male end of the 5’ mini to the RCA cable to one leg of the mini “Y” adaptor. Then connect either the red or black RCA male end of this cable to the “line level input” RCA input (White) on the back of the ButtKicker Power Amplifier.

Connect the signal cable for your speaker system to the other leg of the mini “Y” adaptor.

For a 5.1 sound card, insert the mini “Y” adaptor into the sub/center channel (usually an orange jack). Connect the mini male end of the 5’ mini to RCA cable to one leg of the mini “Y” adaptor. Then connect the red or black RCA male end of this cable to the “line level input” RCA input (White) on the back of the ButtKicker Power Amplifier.

Connect the signal cable for your speaker system to the other leg of the mini “Y” adaptor.

For a multi-channel sound card with a digital output and a separate surround sound system, use the RCA “Y” adaptor to split the “sub out” output of your surround sound processor. Use the 5’ RCA to RCA cable to connect one leg of the RCA “Y” adaptor to the “line level input” RCA input (White) on the back of the ButtKicker Power Amplifier, and connect the audio cable of your subwoofer to the other leg of the RCA “Y” adaptor.

Figure 1

Figure 2

Figure 3

Figure 3b

PLEASE NOTE:

THE QUICK CONNECT CABLE ONLY FITS ONE WAY. Make sure pins are properly aligned with the large pin in the large hole and the small pin in the small hole.

BK-GR2 specifications

The ButtKicker BK-GR2 is a state-of-the-art tactile transducer designed to enhance your audio experience by providing powerful low-frequency vibrations. This innovative device is particularly popular among gamers, movie enthusiasts, and music lovers who seek to immerse themselves fully in their audio environments. The BK-GR2 is built to fit a variety of settings, from home theaters to gaming rigs, ensuring that sound is not only heard but felt.

One of the main features of the ButtKicker BK-GR2 is its ability to produce deep, rumbling vibrations that correspond to the low frequencies in audio content. This includes everything from engine roars in racing games to the deep rumble of bass-heavy music and sound effects in action-packed movies. By translating these low-frequency sounds into physical sensations, the BK-GR2 creates a more engaging and realistic experience, making users feel as if they are part of the action.

The BK-GR2 employs cutting-edge technology, including a powerful transducer that converts audio signals into a tactile response. This transducer operates at a frequency range of 5 Hz to 200 Hz, allowing it to reproduce the most subtle vibrations as well as the most intense bass impacts. The device is designed to provide adjustable intensity levels, giving users control over the degree of tactile feedback based on personal preference and the specific audio content being consumed.

In terms of characteristics, the ButtKicker BK-GR2 is built with durability in mind. Its robust construction ensures it can withstand the demands of regular use, whether in a home theater setup or an intense gaming environment. The unit is easy to install, featuring compatibility with a wide range of audio systems. Simply connect it to an audio source, and it’s ready to amplify your sound experience.

Moreover, the BK-GR2 is equipped with a unique rubber mounting system that helps to isolate the vibrations, minimizing noise and ensuring that the transducer performs efficiently without disturbing others nearby. This makes it suitable for use in various environments, including apartments or shared living spaces.

With its fantastic combination of features, advanced technology, and user-friendly design, the ButtKicker BK-GR2 stands out as an essential tool for anyone looking to enhance their audio experience. Whether you are a casual listener or a dedicated audiophile, the BK-GR2 will take your entertainment to new heights by providing an unparalleled tactile response that revolutionizes the way you experience sound.