HP AD465A manual Network Configuration Worksheet

Page 9

Hardware and Software Installation Procedure

Network Configuration Worksheet

Network Configuration Worksheet

Fill out one worksheet for the networking data of each LAN port on the combination card you are installing.

Table 2

Network Configuration Worksheet

 

 

 

 

 

 

 

 

 

 

Data Type

Required/

Default

How to Configure

Example

Your

 

Optional

(see Note 1)

System

 

 

 

 

 

 

 

 

 

 

 

 

Internet

Required

0.0.0.0

SAM or ifconfig or

196.6.20.2

 

 

Address

 

 

edit

 

 

 

 

 

 

/etc/rc.config.d/

 

 

 

 

 

 

netconf

 

 

 

 

 

 

 

 

 

 

Subnet mask

Required if

Subnet mask not used

SAM or ifconfig or

255.255.248.0

 

 

 

using

 

edit

 

 

 

 

subnetting

 

/etc/rc.config.d/

 

 

 

 

 

 

netconf

 

 

 

 

 

 

 

 

 

 

Station

Built-in but can

As shown on card

SAM or edit

0x0060b0c4012f

 

 

address

be optionally

 

/etc/rc.config.d/

 

 

 

 

changed

 

hpigelanconf or

 

 

 

 

 

 

temporarily:

 

 

 

 

 

 

lanadmin -A

 

 

 

 

 

 

 

 

 

 

Host name

Required if the

None

SAM or edit

host1

 

 

alias for this

system is

 

/etc/hosts

 

 

 

network

connected to

 

 

 

 

 

interface (card)

more than 1

 

 

 

 

 

 

network

 

 

 

 

 

 

 

 

 

 

 

 

Link

Required

Autonegotiating

SAM or temporarily:

lanadmin -X

 

 

configuration

 

 

lanadmin -X

auto_on ppa#

 

 

 

 

 

 

(if already

 

 

 

 

 

 

turned off)

 

 

 

 

 

 

 

 

 

Link

Required

Autonegotiating

Hub or switch (see

lanadmin -X

 

 

speed/duplex

 

 

Note 2) SAM or

100fd ppa#

 

 

mode

 

 

temporarily:

 

 

 

 

 

 

lanadmin -X

 

 

 

 

 

 

 

 

 

 

MTU

Optional

1500 bytes

SAM or edit

lanadmin -M

 

 

(Maximum

 

 

/etc/rc.config.d/

9000 ppa# (see

 

 

Transmission

 

 

hpigelanconf or

Note 3 below)

 

 

Unit): Jumbo

 

 

temporarily:

 

 

 

Frames

 

 

lanadmin -M

 

 

 

 

 

 

 

 

 

 

Receive flow

Optional

On

SAM or edit

lanadmin -X

 

 

control

 

 

/etc/rc.config.d/

fctrl off

 

 

 

 

 

hpigelanconf or

 

 

 

 

 

 

temporarily:

 

 

 

 

 

 

lanadmin -X

 

 

 

 

 

 

 

 

 

Note 1: To configure values permanently, edit the configuration files using SAM or an editor such as “vi”. Using lanadmin will not preserve your settings across reboots.

Note 2: The speed configuration of the card can be 10, 100, or 1000 Mbit/s and is determined by the speed setting of the hub or switch port to which the card is connected. The card automatically senses this speed. The Base-T card only runs at one speed at a time. To verify the speed selection, run lanadmin -x ppa#.

9

Image 9
Contents AB465A PCI-X Legal Notices WarrantyAccess the system card bay Hardware and Software Installation ProcedureInstall the card Connect the card to the networkPrepare to install the software Connect the fibre channel devicesHP-UX 1000Base-T Port Link Partner Resulting Speed Configure the card using SAM Install the latest softwareVerify the LAN installation Verify the fibre channel installation$ifconfig lan PPAnumber ipaddress netmask netmask up For Further Information For Further InformationNetwork Configuration Worksheet Network Configuration WorksheetDescription Fibre Channel Rate Operating Distance Cable SpecificationsAdapter/Extenders Adapter KitPort Fibre Channel Connectors Duplex LC Port Activity/Link LEDs Flashing = Data trafficSolid = Active link OFF = No link Features Interoperability Supported Systems Combination Card in HP Integrity SystemsCombination Card in HP 9000 Systems Physical Specifications ElectricalEnvironmental Electromagnetic Compatibility FCC Statement For U.S.A CanadaEMI Statement European Community Laser Safety Statements Laser Safety Statements