York 291627-YTG-B-0807 warranty Typical Wiring Diagram Notes see Figures 14 Thru, Rollout Switch

Page 28

TYPICAL WIRING DIAGRAM NOTES (SEE FIGURES 14 THRU 17)

1.All field wiring to be accomplished following city, local and/or national codes in effect at time of installation of this unit.

2.Caution: Label all wires prior to disconnection when ser- vicing controls. Wiring errors can cause improper and dangerous operation. If any of the wire as supplied with this unit must be removed it must be replaced with type 105°C, 600V wire or equivalent clearly renumbered for identification. Verify proper operation after servicing.

3.Motors inherently protected.

4.Factory wired for 460V operation.

5.See unit nameplate for maximum fuse size and/or circuit breaker size and minimum circuit ampacity.

6.If both LR and ASCT are present, wire 801/BL and 805/ BL are connected to ASCT-3. If only LR is present wire 801/BL and 805/BL are connected to M1 coil. If only

291627-YTG-B-0807

ASCT is present wire 202/Y is connected to ASCT-3. If neither LR or ASCT are present, wire 202/Y is connected to M1 coil as shown.

7.Shunt contact also used with crankcase heater. (optional)

8.Unit factory wired for low or medium speed indoor blower operation. To change motor speed, connect speed tap wires from indoor blower motor, per Detail A (Figure 19). Tape unused speed tap wires to prevent shorting and secure.

9.Select indoor blower speed to remain within the temper- ature rise range on the nameplate in heating.

Open all disconnects before servicing this unit.

 

LEGEND

ALS

AUXILARY LIMIT SWITCH

ASCT

ANTI-SHORT CYCLE TIMER (OPTIONAL)

BR

BLOWER RELAY

CB

CIRCUIT BREAKER

CCH

CRANK CASE HEATER (OPTIONAL)

COMPR

COMPRESSOR

DM

DRAFT MOTOR

FCB

FAN CONTROL BOARD

GND

GROUND

FS

FREEZE STAT SWITCH (OPTIONAL)

HP

HIGH PRESSURE SWITCH OPENS @ 380 PSIG

IDFAN

INDOOR FAN MOTOR

LP

LOW PRESSURE SWITCH OPENS @ 7 PSIG

LS

LIMIT SWITCH

LR

LOCK OUT RELAY (OPTIONAL)

M1

CONTACTOR, COMPR. AND OD FAN

ODFAN

OUTDOOR FAN MOTOR

PS

PRESSURE SWITCH

RC1 / RC2

COMPRESSOR START & OUTDOOR FAN RUN CAPACITOR

RS

ROLLOUT SWITCH

TB4

TERMINAL BLOCK

T1

TRANSFORMER, 24V, 230V

T2

TRANSFORMER, 460V / 575V

FIGURE 18 - TYPICAL WIRING DIAGRAM LEGEND

28

Unitary Products Group

Image 28
Contents General Flexible Light Commercial UnitFeaturing Table of Contents Standard FEATURES/BENEFITS DescriptionFIELD-INSTALLED Accessories High Altitude Conversion KIT Natural Gas/PropaneUnit Component Location Physical Data Model DNHRise Ratings COOLING/GAS HeatingMBH Burners Range DNH030 Cooling Capacities 2-1/2 TON Temperature AIR on Evaporator CoilAIR on WB F Condenser Coil DNH036 Cooling Capacities 3 TON DNH042 Cooling Capacities 3-1/2 TON DNH048 Cooling Capacities 4 TON DNH060 Cooling Capacities 5 TON Model # External Staic Pressure IWG DNH MTR Side Supply AIR Blower Performance 208 VOLT1SPD Side Supply AIR Blower Performance 230 & 460 VOLT1 Model # External Static Pressure IWG MTR DNHBottom Supply AIR Blower Performance 208 VOLT1 Bottom Supply AIR Blower Performance 230 & 460 VOLTS1 Additional Static Pressure Resistance 2-1/2 3 TON DNH030Typical Field Control Wiring Diagram Additional Static Pressure Resistance 3-1/2 5 TON DNH042Electrical Data Unit Minimum CLEARANCES1 Unit Size DimensionClearances Unit Dimensions Front & Bottom Typical Slab on Ground Installation D133 Roof Curb DIMENSIONS1 YTG-B-0807 YTG-B-0807 Typical Wiring Diagram DNH 060 208-230-3-60 Power Supply Typical Wiring Diagram DNH 060 460-3-60 Power Supply Typical Wiring Diagram Notes see Figures 14 Thru Rollout SwitchCompressor Start & Outdoor FAN RUN Capacitor TB4 Terminal Block TRANSFORMER, 24V TRANSFORMER, 460VMechanical Specifications DescriptionRefrigerant Components YTG-B-0807 YTG-B-0807

291627-YTG-B-0807 specifications

York 291627-YTG-B-0807 is a sophisticated air conditioning unit designed to deliver both efficiency and comfort in various environments. This model is part of York's advanced line of HVAC solutions, catering to residential and commercial applications. With its focus on energy efficiency, longevity, and reliability, the York 291627-YTG-B-0807 addresses the needs of modern users who seek sustainable climate control without sacrificing performance.

One of the main features of the York 291627-YTG-B-0807 is its high-efficiency SEER (Seasonal Energy Efficiency Ratio) rating. This rating is a critical metric for determining the unit's energy consumption versus its cooling output, making it an excellent choice for users looking to minimize electricity costs while maintaining optimal indoor temperatures. The unit is designed with advanced compressor technology that not only enhances efficiency but also ensures quieter operation, making it suitable for noise-sensitive environments.

Another notable characteristic of this model is its use of environmentally-friendly refrigerants. The York 291627-YTG-B-0807 utilizes refrigerants with a lower global warming potential and higher cooling efficiency. This aligns with the growing demand for environmentally conscious solutions, allowing businesses and homeowners to reduce their carbon footprint without compromising cooling power.

Additionally, the technology embedded in the York 291627-YTG-B-0807 incorporates smart features for enhanced user control. The unit is compatible with smart thermostats, allowing users to manage their cooling settings remotely through mobile applications. This connectivity enables greater flexibility in adjusting temperature settings based on actual usage patterns, which can result in further energy savings.

The build quality of the York 291627-YTG-B-0807 is robust, featuring a durable cabinet that can withstand various weather conditions. It is designed to operate efficiently and effectively in diverse climates, ensuring reliable performance throughout the year. Furthermore, the unit is backed by a comprehensive warranty, providing users with peace of mind regarding their investment.

In summary, the York 291627-YTG-B-0807 is an exceptional air conditioning solution that combines high efficiency, eco-friendly technologies, and smart features to meet the needs of contemporary users. Its reliability, performance, and ease of use make it a standout choice for those seeking a high-quality cooling solution that aligns with environmental standards while enhancing comfort in homes and businesses alike.