Description, Specifications, Performance Chart

Specifications Information and Replacement Parts Manual	4445-95,	4446-95, 5570-95,
	5571-95,	5572-95

Please read and save this Repair Parts Manual. Read this manual and the General Operating Instructions carefully before attempting to assemble, operate or maintain the product described. Protect yourself and others by observing all safety information. The Safety Instructions are contained in the General Operating Instructions. Failure to comply with the safety instructions accompanying this product could result in personal injury and/or property damage! Retain instructions for future reference.

Vertical Sealless Sprayer/Washer Pumps

Refer to form 1608-634-00 for General Operating and Safety Instructions and applicable Warranty.

Description

Vertical sealless sprayer/washer pumps are heavy duty industrial units designed for OEM, automotive and industrial washing machines, parts cleaners, spray booths and cooling towers. Pumps are immersion type; pump end must be immersed in liquid, motor must remain above liquid surface.

All models feature 316 stainless steel semi-open clog resistant impeller, stainless steel shaft, steel shaft coupling, cast iron base and column, plated steel inlet screen, and a TEFC (Totally Enclosed Fan Cooled) electric motor. Motor has ball bearings. Heavy- duty steel universal mounting brackets included. Pump design eliminates a bottom bearing and a shaft seal on all models. Pumps handle liquids up to a maximum temperature of 200° F. Maximum ambient temperature 104° F. Liquid viscosity cannot exceed 100 SSU. These are manual units; no controls are supplied. For use with nonflammable liquids compatible with pump component materials.

Specifications

		DRIVER		NEMA	DIS. Outlet	Weight
Model	HP	Power Supply	RPM	Frame	(Inches)*	(Lbs.)
4445-95	3	230 VAC, 60 Hz. 1-phase	3450	56C	1-½	78
4446-95	3	230 VAC, 60 Hz. 3-phase	3450	56C	1-½	73
5570-95	10	230/460 VAC, 60 Hz. 3-phase	3450	184JM	1-½	165
5571-95	7.5	230/460 VAC, 60 Hz. 3-phase	3450	184JM	1-½	150
5572-95	5	230/460 VAC, 60 Hz. 3-phase	3450	184JM	1-½	130

NOTE: Driver data is subject to change without notice, see label on driver for actual specifications.

(*) Standard NPT (female) pipe thread

Performance Chart

						GPM of Water at Total Head in Feet						Max.
Model	HP	60	70	80	90	100	110	120	130	140	150	Head†
4445-95	3	80	55	25	-	-	-	-	-	-	-	85 ft.
4446-95	3	80	55	25	-	-	-	-	-	-	-	85 ft.
5572-95	5	*	115	100	80	50	-	-	-	-	-	110 ft.

5571-95	7.5	*	*	140	125	110	90	70	40	-	-	140 ft.
5570-95	10	*	*	*	162	150	135	120	95	70	40	160 ft.

(*)Operation of pumps beyond range indicated will result in reduced pump life, pump damage and/or motor damage. (†) Shut-off; convert to psi, multiply by specific gravity and divide by 2.31

Installation

1.(5570 series pumps) Remove shipping fixture (Ref. No. 19) that holds the drive shaft to the base before installing pump.

2.Pump must be installed with its base supporting the entire weight of the pump.

CAUTION Mounting brackets are not designed to support the pump’s weight. Brackets are designed to prevent tipping.

3.Position pump in tank or reservoir. Position mounting brackets, align pipe clearance hole with pump discharge outlet.

(4445 series pumps)

4.Assemble one piece of sponge tape (Ref. No. 25) to each clamp bracket (Ref. No. 24). Attach clamp brackets to mounting brackets with fasteners provided (Ref. Nos. 26 and 27). This will fix the column (Ref. No. 3) in position.

(5570 series pumps)

4.Adjust lower fasteners (Ref. No. 4) to bottom of mounting brackets. Secure pump to mounting brackets with upper fasteners (Ref. No. 4).

5.Secure mounting brackets to tank or reservoir. Install an appropriate fastener in each hole or slot provided.

6.Install the balance of the system.

5570-250-00 03/2006