HP 7.25 manual Cleaning, Deck Lubrication, To apply lubricant to the walking belt

Page 39

www.smoothfitness.com

39

MAINTAINENCE

CLEANING:

Routine cleaning of your treadmill will extend the product's life.

•Warning: To prevent electrical shock, be sure the power to the treadmill is OFF and the power cord is unplugged from the wall electrical outlet before attempting any cleaning or maintenance.

•Important: Never use abrasives or solvents to clean the treadmill. To prevent damage to the computer, keep liquids away and keep it out of direct sunlight.

•After each workout: Wipe off the console and other treadmill surfaces with a clean, water dampened soft cloth to remove excess perspiration.

•Weekly: Use of a treadmill mat is recommended for ease of cleaning. Dirt from your shoes contacts the belt and eventually makes it to underneath the treadmill. Vacuum underneath treadmill once a week.

DECK LUBRICATION:

The walking belt has been pre-lubricated at the factory. However, it is recommended that the walking board be checked periodically for lubrication to ensure optimal treadmill performance. Your treadmill should not have to be lubricated usually within the first 400 hours of use.

Every 2 months of operation lift the sides of the walking belt and feel the top surface of the walking board as far as you can reach. If you feel signs of silicone, no further lubrication is required. If it feels dry to the touch, follow the instructions below.

Please use Lube 'N Walk (can be purchased from your dealer or call the number on the front of the manual), or a non-petroleum based silicone such as "Napa 8300" (available at most stores).

To apply lubricant to the walking belt:

1.Position the walking belt so that the seam is located on top and in center of the walking board.

2.Insert the spray nozzle into the spray head of the lubricant can.

3.While lifting the side of the walking belt, position the spray nozzle between the walking belt and the board approximately 6" from the front of the treadmill. Apply the silicone spray to the walking board, moving from the front of the treadmill to the rear. Repeat this on the other side of the belt. Spray approximately 4 seconds on each side.

4.Allow the silicone to "set" for 1 minute before using the treadmill.

Spray lubricant from front to back.

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Model Number Motorized TreadmillPrecautions PrecautionsPower Requirements Power RequirementsPreassembly Contents Checklist Hardware Comparison Chart Hardware chartMillimeters 25-100 Console Assembly Parts List25-400 25-600 10 7.25 Treadmill Parts List Parts Diagram 805 801 207 208 209 204 804 205 206 201 203 202 14 7.25 Treadmill Parts Diagram Treadmill 603 601 832 809 604 605 822 818 602703 702 704 840 814 707 706 Step Assembly804 805 805 204 301 806 807 807 301 24 7.25 Treadmill Follow These Instructions to Level Your Treadmill Stabilizer AdjustmentFolding Instructions How to fold treadmillUnfolding Instructions How to unfold treadmillTransport Instructions Transport InstructionsScan/Hold Button FunctionsStart Stop / EnterComputer Operation Cool Down SET UP User InformationOperating Instructions Quick Start Pause / StopProgram 3 Target Calories Select Operating ProgramProgram 1 Target Time Program 2 Target DistanceProgram 7 5K Self Learing and Competition Program 6 Weight LostProgram 4 Interval Incline Program 5 Interval Speed34 7.25 Treadmill C1 C3 Custom Program User Program SET and Save the User ProgramEdit Previous Saved Program 36 7.25 Treadmill Motion Control Operation HOW to Maintain the Treadmill Belt AdjustmentMaintainence Cleaning Deck LubricationTo apply lubricant to the walking belt Frame Drive Electronics Parts Labor Motor WarrantyBefore beginning Important StepsTarget Heart Rate Finding your pulseAerobic exercise Muscle Groups Muscle ChartStretching Routine Treadmill walking belt slows during use TroubleshootingTroubleshooting Treadmill will not start Treadmill looses power during useSmooth Fitness PO BOX Farnborough GU14 4BS United Kingdom
Top Page Image Contents