HP 2510xi manual 10a Wired network setup, 10b Wireless network setup infrastructure, Windows Users

Side 2 - Start on other side.

For the most up-to-date information on network setup, see www. hp.com/support

10a Wired network setup

WINDOWS

USERS:

Wired setup allows your
HP PSC to communicate to	1	2	3	4
your computers through a				Choose
router/hub/switch.
				Windows or
				Macintosh,
				and then follow
				the steps carefully.

Follow these boxed steps for each computer that is part of the wired network.

5	6	7	8
Turn on your	Insert the HP PSC	Choose Through the	Choose the second
computer and wait	Windows CD and	network as your	option, connect
for the desktop to	then, follow the	connection type.	using a network
appear.	onscreen		cable as your
Make sure you are	instructions.		connection type.
logged onto the
network.
Disable any firewall
software.

9	10	11
Complete the rest of	After your computer	Congratulations!
the onscreen	restarts, follow all	You are ready
instructions.	onscreen instructions	to use the HP PSC.
	including the Fax
	Setup Wizard.

hp psc 2500

photosmart series

all-in-one

reference guide

If you have any questions, see the Wired Network Setup chapter in the Reference Guide.

ETHERNET
Remove the yellow	Connect the
plug from the	ETHERNET
ETHERNET jack.	cable to the
Connect the	hub/router/
ETHERNET cable to	switch.
the back of the
HP PSC.

NOTE: You can use the cable from the box or purchase a longer cable.

STOP! Make sure the blue network light on the HP PSC is lit. This might take 60 seconds.

MACINTOSH USERS:

5	6	7	8	9	10	11
					10	11
Turn on your	Insert the HP PSC	Double-click the HP	In the first dialog	Choose wired	Complete all onscreen	Congratulations!
computer and wait	Macintosh CD.	All-In-One Installer	box, you must select	network as your	instructions including	You are ready
for the desktop to		icon on your folder.	Network as the	connection type.	the Setup Assistant.	to use the
appear.			device connection		In the Select Device	HP PSC.
			type.		dialog box, make
Make sure you are					sure TCP/IP
logged onto the					(network) is
network.					selected.
Disable any
firewall software.

2

10b Wireless network setup (infrastructure)

Follow these boxed steps for each computer that is part of the wireless network.

Poster - Side

Wireless setup allows your

HP PSC to communicate to your computers through a wireless

access point or base station. 1 2 3

4	5
In the box below,	Choose
write down the	Windows or
information listed.	Macintosh,
Use during step	and then follow
10. If you are	the steps carefully.
unsure, see the
documentation or
web page for the
access point/base
station.

WINDOWS	6	7		8	9
USERS:	Turn on your	Insert the HP PSC		Choose Through	Choose connect
	computer and wait	Windows CD and		the network as	using wireless
	for the desktop to	then, follow the		your connection	communication
	appear.	onscreen		type.	as your connection
	Make sure you are	instructions.			type.
	logged onto the
	network.
	Disable any
	firewall software.
				12
	6	7	8		9

10	11	12
Complete the rest of	When you see the	After your
the onscreen	Unplug Cable	computer restarts,
instructions. Enter the	dialog box,	complete all
information your	disconnect the	onscreen
wrote down earlier.	cable from your	instructions
Make sure the blue	HP PSC and	including the Fax
	access point.	Setup Wizard.
network light is		Congratulations!
steady. Refer to the
		You are ready
Reference Guide for
		to use the HP PSC.
help.

10	11	12
10	11

ETHERNET

MACINTOSH

Network Setup

Remove the yellow	Connect the
plug from the	ETHERNET
ETHERNET jack.	cable to the
Connect the	access point.
ETHERNET cable to	(You will remove
the back of the	this later.)
HP PSC.

STOP! Make sure the blue network light on the

HP PSC is lit. This might take 60 seconds.

SSID

/Network Name:

WEP Key/Password (if applicable):

For Macintosh, this is called Network Name and Password.

USERS:	Turn on your	Insert the HP PSC	In the first dialog	Choose wireless
	computer and wait	Macintosh CD.	box, you must select	network as your
	for the desktop to		Network as the	connection type.
	appear.		device connection
	Make sure you are		type.
	logged onto the
	network.
	Disable any	Double-click the
		HP All-In-One
	firewall software.	Installer icon on
		your desktop.

Enter the information that you wrote down earlier.

Make sure the blue network light is steady. Refer to the Reference Guide for help.

Complete all	Congratulations!
onscreen	You are ready
instructions	to use the HP PSC.
including the
Setup Assistant. In
the Select Device
dialog box, make
sure
TCP/IP
(network) is
selected.

hp psc 2500

photosmart series

all-in-one

reference guide

If you have any questions, see the Wireless Network Setup chapter in the Reference Guide.

For the most up-to-date information on network setup, see www. hp.com/support