Testing Your Wood, First Fires, Ignition | United States Stove 2015

TESTING YOUR WOOD

When the stove is thoroughly warmed, place one piece of split wood (about five inches in diameter) parallel to the door on the bed of red embers.

Keep the air control full open by pulling on it and close the door. If ignition of the piece is accomplished within 90 seconds from the time if was placed in the stove, your wood is correctly dried. If ignition takes longer, your wood is damp.

If your wood hisses and water or vapour escapes at the ends of the piece, your wood is soaked or freshly cut. Do not use this wood in your stove. Large amounts of creosote could be deposited in your chimney, creating potential conditions for a chimney fire.

THE FIRST FIRES

The fresh paint on your stove needs to be cured to preserve its quality. Once the fuel charge is properly ignited, only burn small fires in your stove for the first four hours of operation. Never open the air control more than necessary to achieve a medium burn rate.

Make sure that there’s enough air circulation while curing the stove. The odors could be smelled during the 3 or 4 first fires. Never start your stove outside. You will not be able to see if you are over heating.

IGNITION

After making sure that the stove air intake controls are fully open (completely pull-out towards you), place several rumpled sheets of paper in the centre of the combustion chamber. Place 8 to 10 pieces of small dry kindling wood over the paper in the form of a tent. You may also place a few pieces of heating wood, but choose the smaller ones. No chemical product should be used to light the fire.

Before igniting the paper and kindling wood, it is recommended that you warm up the chimney. This is done in order to avoid back draft problems often due to negative pressure in the house. If such is the case, open a window slightly near the stove and twist together a few sheets of newspaper into a torch. Light up this paper torch and hold it as close as possible to the mouth of the pipe inside the combustion chamber to warm up the chimney. Once the updraft movement is initiated, you are ready to ignite the stove by lighting the paper and kindling wood inside the combustion chamber.

We therefore advise you to leave the door slightly opened (1/4") for a 10 to 30 minutes period, under supervision, in order to allow for good combustion. After this time, you must close the door and progressively adjust the air control to obtain the desired temperature.

HEATING

Controlled combustion is the most efficient technique for wood heating because it enables you to select the type of combustion you want for each given situation. The wood will burn slowly if the wood stove air intake control is adjusted to reduce the oxygen supply in the combustion chamber to a minimum. On the other hand, wood will burn quickly if the air control is adjusted to admit a larger quantity of oxygen in the combustion chamber. The air intake control on your stove is very simple. If you pull on it out completely towards you, it is fully open. If you push on it until it stops the combustion air is reduced to a minimum. Your Magnolia stove burned between .954 kg\h et 2.556 kg\h. of wood during EPA testing. Real operating conditions may give very different results than those obtained in the lab according to the species of wood used, its moisture content, the size and density of the pieces, the length of the chimney, altitude and outside temperature.

Ussc

2015 specifications

United States Stove Company has been a central figure in the heating industry for over 150 years, renowned for its commitment to crafting reliable, efficient, and innovative wood and pellet stoves. In 2015, the company continued to build on its legacy with a range of products that showcased modern technologies while maintaining traditional craftsmanship.

One notable feature of United States Stove's 2015 offerings was the integration of advanced combustion technology. This innovation allowed for cleaner burning and improved fuel efficiency, making their stoves more environmentally friendly than ever. By optimizing the combustion process, the stoves reduced emissions, complying with stringent EPA regulations and helping homeowners lower their carbon footprint.

Another key characteristic of their products in 2015 was the use of high-quality materials. United States Stove Company stoves were built with durable cast iron and steel, ensuring longevity and improved heat retention. The robust construction not only contributed to the stoves' durability but also provided a classic aesthetic that appealed to traditional and modern home designs alike.

In terms of user experience, 2015 models were equipped with features that emphasized ease of use and convenience. Many units included adjustable airflow settings, allowing users to control the intensity of the heat output easily. Additionally, several models came with large viewing windows, providing an unobstructed view of the flames, which enhanced the overall ambiance of any living space.

United States Stove also prioritized safety in their designs. Many of the 2015 models were fitted with safety features such as overheat protection systems and heat-resistant door handles. This commitment to safety ensured that users could enjoy the warmth and comfort of their stoves with peace of mind.

Moreover, the adaptability of their products was evident in the variety of models available. From compact units suitable for smaller spaces to larger freestanding models capable of heating expansive areas, United States Stove catered to a wide range of customer needs. This versatility made it easier for homeowners to find a solution that best fit their heating requirements.

In summary, United States Stove Company's 2015 lineup was marked by advanced technologies, durable materials, user-friendly features, and a strong focus on safety. This combination of elements not only reflected the company’s commitment to quality and innovation but also solidified its reputation as a trusted leader in the heating industry for generations to come.