HP Enterprise File Services WAN Accelerator manual Setting Main Static Routes

Page 59

 

4. Use the controls to complete the configuration, as described in the following table.

 

 

 

Control

 

Description

 

 

 

AUX Interface Enabled

 

Select Enabled or Disabled from the drop-down list.

 

 

IMPORTANT: The primary and auxiliary interfaces cannot share the same network

 

 

subnet. The auxiliary and in-path interfaces cannot share the same subnet. You cannot use

 

 

the auxiliary port for out-of-path HP EFS WAN Accelerators.

 

 

 

IP Address

 

Obtain IP address automatically. Specify this option to obtain the IP address from a

 

 

dynamic host configuration protocol (DHCP) server.

 

 

 

 

 

Specify IP Address Manually. Specify this option if you do not use a DHCP server to

 

 

set the IP address. Specify the following settings:

 

 

• IP Address. Specify an IP address.

 

 

• Subnet Mask. Specify the subnet mask.

 

 

 

Additional Interface Settings

 

Speed. Select the speed from the drop-down list to set the speed for the auxiliary

 

 

interface. The default value is Auto.

 

 

If your network routers or switches do not automatically negotiate the speed and duplex,

 

 

you must set the speed and duplex manually.

 

 

 

 

 

Duplex. Select Auto, Full, or Half from the drop-down list to set the duplex speed for the

 

 

auxiliary interface. The default value is Auto.

 

 

If your network routers or switches do not automatically negotiate the speed and duplex,

 

 

you must set the speed and duplex manually.

 

 

 

 

 

MTU. Specify the Maximum Transmission Unit (MTU) value. The MTU is the largest

 

 

physical packet size, measured in Bytes, that a network can transmit. The default is 1500.

 

 

 

2 CONFIGURING THE HP EFS WAN ACCELERATOR

Setting Main Static Routes

5.Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)

6.Click Save to save your settings permanently or click Reset to return the settings to their previous values.

You set static routes for device management or out-of-path network configurations in the Host Settings - Routing: Main page.

Main static network routes set routing rules in the main routing table for the primary interface.

HP STORAGEWORKS EFS WAN ACCELERATOR MANAGEMENT CONSOLE USER GUIDE

59

Page 58 Page 60
Image 59
Page 58 Page 60
Contents User guide Page Contents Setting QoS Marking Setting Host ParametersSetting the DNS Setting ProxiesChapter Creating HP EFS WAN Accelerator Reports and Logs 147 Glossary 225 Index 229 Appendix a HP EFS WAN Accelerator Ports 203Appendix B HP EFS WAN Accelerator MIB 209 This Introduction About This GuideOrganization of This Guide Document Conventions Hardware and Software DependenciesAntivirus Compatibility Ethernet Network CompatibilityAdditional Resources Related Reading Contacting HPIntroduction This Chapter Connecting to the Management ConsoleConnecting to the Management Console Management Console To connect toHome Welcome Navigating in the Management Console Navigating in the Management ConsoleOverview of the HP EFS WAN Accelerator Restarting the HP Saving Your ConfigurationAccelerator Service Tabbed Pages and MenusTo display online help Displaying OnlineHelp Logging OutOverview of the HP EFS WAN Accelerator Management Console Configuring the HP EFS WAN Accelerator Enabling Path and Out-of Path Support Setting Optimization ServicesOptimization Service General Settings To enable in-path or out-of-path supportControl Description 4096 Setting In-Path RulesAppendix A, HP EFS WAN Accelerator Ports Port labels, see Creating Port Labels on Click Remove Selected Rules FTP Modifying Path Descriptions To modify your in-path rule description Configuring Cifs Protocol SupportProtocol options To configure CifsConfiguration Guide Slddwg, sldprt, txt, vsd, xls Configuring Mapi Protocol OptionsOptimizing Mapi Exchange in Out- of-Path Deployments Optimization Service Protocol Mapi To configure MapiConfiguring MS SQL Protocol Options Click Remove Selected Ports Optimization Service Protocol MS-SQLApplication Streamlining To enable the NFS optimizerEnabling Click Remove Selected Servers Server SettingsService Protocol NFS Server server name Modifying NFSOptimization Service Protocol NFS Server server name Control Description Task Description Enabling Hstcp Protocol OptionsControlDescription Protocol support To enable HstcpEnabling Connection Pooling 10.Optimization Service Connection Pooling Enabling Transparent Prepopulation To enable prepopulation settings\\origin-file-server\local-name Enabling Synchronizing Prepopulation Shares12.Prepopulation Settings and Shares Details To modify Share SettingsSettings ModifyingExample, \\origin-file-server\local-name Performing Manual Actions on Prepopulation SharesUse the controls to modify your values Following table To perform manualActions on Prepopulation sharesSetting Primary Interface Setting Host ParametersInterface To set the primary1500 Speed and Duplex TipsTo set the in-path IP address. Specify the following settings Vlan 17.Host Settings Interface AUX Setting Auxiliary InterfacesSetting Main Static Routes Click Remove Selected Routes To set a static main routeHP recommends you use DNS Setting the DNSClick Remove Selected Domain To their previous valuesTo modify the host name Modifying the Host NameTo map a host name to an IP address Setting ProxiesTo enable a proxy Setting Advanced Network ParametersSetting proxies is optional Enabling Asymmetric Routing Auto Detection Click Remove Selected Entries 24.Advanced Networking Asymmetric Routing25.Asymmetric Network Enabling Connection Forwarding26.Advanced Networking Connection Forwarding Entries Enabling Encryption27.Advanced Networking Encryption Click Remove Selected Peers Enabling Failover Data Store Synchronization Synchronization To enable failoverData store For detailed information, see Setting In-Path Interfaces on Automated Online Datastore Enabling NetFlow support is optional Enabling NetFlowSupport To enable NetFlowControlDescription Add New Entry Setting Peering RulesEnabling Peering Rules for Serial Clustering 30.Advanced Networking Peering Rules To set a peering ruleFormat XXX.XXX.XXX.XXX/XX Quality ServiceTraffic Classification To enable QoSClassification 31.Advanced Networking QoS Classification Control Description Modifying a QoS Class 32.Advanced Networking QoS Classification Setting QoS Marking 33.Advanced Networking QoS Marking Modifying QoS Marking Descriptions To modify your QoS rule description Modifying Service Ports35.Advanced Networking Service Ports To set a service portEnabling Simplified Routing Control To enable simplifiedRouting RoutingEnabling Wccp Groups Groups To enable a WccpService group Groups Modifying Wccp Group SettingsTo modify Wccp Service group settingsClick Wccp Groups to display the Wccp Service Groups Wccp Service Group Group IDTo determine traffic to redirect HP EFS WAN Accelerator. It includes the following sections Enabling Proxy File ServiceConfiguration Enabling PFS39.Proxy File Service PFS Configuration To enable PFS101 Required Adding PFS SharesParameters Click Proxy File Service to expand the PFS menuClick Shares to display the Proxy File Service Shares To set PFS share104 V3.x on105 Domain\Administrator106 To initialize and enable a shareEnabling Synchronizing Shares 107 Upgrading Shares from V2.x to42.Proxy File Service PFS Shares Details Necessary to configure109 SettingsSettings Modifying ShareDisplayed To modify share111 To perform manual actions on shares Performing Manual Actions on Shares113 Creating Port LabelsCreating Port Labels Port Type Description and Ports114 Labels115 Setting Report ParametersTo modify ports in a port label To set alarm parameters Setting Alarm Parameters117 Setting Email NotificationTraps on To set event and failure email notification119 Setting Snmp ParametersTo set Snmp parameters To set an Snmp trap Setting Snmp Trap Receivers121 Click Remove Selected Receivers122 Update All PortsLogging Setting Logging OptionsSetting Local To set up local loggingTo set up remote logging Setting Remote LoggingTime Setting the Date and TimeTime To set the dateTo set an NTP server Setting NTP Servers127 Setting Authentication MethodsTo set an Authentication method129 Setting Administrative PasswordTo set Setting Monitor PasswordAdministrator Password131 Setting Radius ServersTo set the monitor 59.Authentication Radius Servers 133 SettingServers Allowed to a given systemServer To set a TACACS+135 Modifying Web SettingsTo modify Web Setting Message Day Motd137 Managing LicensesTo set a Motd Click Licenses to display the Licenses To update a licenseThis section describes how to view scheduled jobs Viewing Scheduled Jobs139 Managing ConfigurationsTo view scheduled jobs 140 141 ConfigurationsEntry and click Remove Selected Configuration To manageUpgrading Your Software Configuration143 To upgrade or revertSoftware versions To start, stop, or Starting and Stopping ServicesRestart services WAN Accelerator Rebooting the HP EFS WAN AcceleratorClick Reboot Appliance to display the Reboot Appliance Shutting Down the HP EFS WAN AcceleratorEFS WAN Accelerator To shutdown the HP147 Contents. This chapter includes the following sectionsCreating Performance Reports Field Description Creating Bandwidth Optimization ReportsWhat this Report Tells You About Report Graphs 149 About Report DataTo create a Bandwidth Optimization report What This Report Tells You Creating Data Store Hits Reports151 About Report Graphs About Report DataPerformance Data Store Hits Creating Data Reduction ReportsTo create the Data Store Hits report153 Performance Data Reduction Reduction report155 Creating NFS Statistics ReportStatistics report Time at which the peak occurredAggregate for the time period selected To create the NFS157 Creating Throughput ReportsThroughput To createThroughput report 159 Creating Traffic Summary Reports160 161 To create the TrafficSummary report Performance Traffic Summary162 Viewing Appliance ReportsViewing Data Store Reports Optimized163 Viewing TCPStatistics Report To create the Data Store reportPacket Type Description 164165 Viewing Networking ReportsTo create the TCP TCP Statistics166 Viewing Connected Appliances ReportsReport ViewingHistory Connected Appliances168 169 Connection HistoryConnection History Viewing Current Connections 171 To create the Current Connections reportViewing Current Connection Details Report 173 Current Connections Viewing Connection PoolingTo view current Connection details‹ How many connections occurred? What This ReportTells You ‹ How large is the pool of connections?Connection Pooling Connection Pooling‹ How many packets am I transmitting? ‹ How many errors are there in each transmission?‹ What is the current status of my interface? Duplex, MAC address, and current status for each interfaceInterface Statistics Creating Link State ReportsTo view Interface Statistics179 State To create the LinkState report 181 CreatingNeighbor Statistic Reports16.Network Neighbor Statistics Creating QoS Statistics Reports183 Statistics To create the QoS185 Alarm DescriptionViewing System Health Reports HP EFS WAN Accelerator on page 145 and Starting 187 99 and Starting and Stopping Services onStatus To create the AlarmCreating CPU Utilization Reports Status report189 To create the CPUUtilization report Utilization190 Creating Memory Paging Reports191 To create MemoryPaging report Memory PagingViewing PFS Share Status Reports Viewing Proxy File Service Reports193 Viewing PFSSpecified 194 195 Name-of-Share report196 Exporting Performance Statistics ReportsExporting Performance Statistics To export statistics197 Viewing System Diagnostic FilesViewing System Snapshots 199 Viewing TCP Dump FilesTo view system snapshot files TCP Dump Viewing HP EFS WAN Accelerator LogsTo view TCP dump Files201 Accelerator LogsAccelerator logs 202 To view online help contentsGetting Help Contacting Technical Support203 Default PortsDefault Ports Description Application Ports Commonly Optimized PortsCommonly Excluded Ports ‹ 445 Cifstcp ‹ 1812 Radius ‹ 7830 Mapi205 Interactive Ports Forwarded by the HP EFS WAN AcceleratorPort Description Type Port Description Secure Ports Forwarded by the HP EFS WAN Accelerator207 IEEE-MMS-SSLSIP-TLS 209 Accessing the HP EFS WAN Accelerator Enterprise MIBTrap Description Snmp Traps211 HP EFS WAN Accelerator Enterprise MIBHP EFS WAN Accelerator MIB 213 214 215 Alarms216 217 Statistics 218219 220 221 222 END 223224 225 Glossary226 227 228 229 Index230 In-path231 232 Snmp
Related manuals
Manual 1 pages 12.03 Kb Manual 38 pages 24.46 Kb Manual 14 pages 52.65 Kb Manual 124 pages 48.85 Kb
Top Page Image Contents