Lochinvar 402 - 2072 service manual Temp O/Shoot, Rem Ctrl Flt, Parameters Progr

Page 42

Copper-fin II/IIE Boiler and Water Heater Service Manual

3 Troubleshooting

Table 3E (continued from previous page) Troubleshooting Chart - Fault Messages Displayed on Operator Interface

FAULT

DESCRIPTION

CORRECTIVE ACTION

 

 

 

 

The temperature rise across the heat

• Verify that the system is full of water and that all air

 

exchanger has exceeded the set parameters

has been properly purged from the system.

 

for the appliance.

• Verify that the appliance is piped properly into the

 

 

 

 

heating system. Refer to the Water Connections

 

 

Section of the Installation and Operation Manual for the

 

 

proper piping methods.

 

 

• Check for 120 VAC to the pump motor on a call

 

 

for heat. If voltage is not present, check the wiring

 

 

leading to the main control board. Replace the main

Temp O/Shoot

 

control board if necessary.

 

• If 120 VAC is present on a call for heat and the

(Lockout will reset

 

automatically after 5

 

pump is not operating, replace the pump.

minutes or may be

 

 

 

 

reset immediately once

Outlet water temperature has exceeded the

• Verify that the system is full of water and that all air

condition has been

maximum outlet water temperature.

has been properly purged from the system.

corrected. Press the

 

 

RESET button on the

 

• Verify that the appliance is piped properly into the

SMART SYSTEM display

 

system. Refer to the Water Connections Section of

to reset.)

 

the Installation and Operation Manual for the proper

 

 

piping methods.

 

 

• Check 120 VAC to the pump motor on a call for heat.

 

 

If voltage is not present, check wiring leading to the

 

 

main control board. Replace the main control board

 

 

if necessary.

 

 

• If 120 VAC is present on a call for heat and the pump

 

 

is not operating, replace pump.

 

 

• Replace the main control board.

 

 

 

 

 

• Check setpoint of the external control.

Rem Ctrl Flt

External control is cycling too often.

• Check the wiring between the external control and

 

the unit.

 

 

 

 

• Replace the control.

 

 

 

Parameters Progr

 

 

(Will require a manual

 

• Press the ENTER/RESET button on the Smart

reset once the condition

After downloading parameters from a laptop,

has been corrected. Press

the main control board must be reset.

System display panel.

the RESET button on the

 

 

SMART SYSTEM display

 

 

to reset.)

 

 

 

 

 

42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Copper-fin II/IIE Boiler and Water Heater Models 402 Contents Please read before proceeding Handling ceramic fiber materialsNiosh stated First Aid Maintenance What is in this manual?Service TroubleshootingService Copper-fin displayControl inputs Control outputs How the control module operates General OperationHow the appliance operates Sequence of operationSequence of operation OUT 123.8F129HTR Postpurge Display panel menu access Display panel parameter access Parameter table a Boiler Operation OnlyAnti-cycle Time Anti Cycl Tm Parameter table B Water Heater Operation BMS Service Notification Pumps Temperature settings Viewable and changeable control parametersData logging FunctionsDHW settings Outdoor air reset boiler only Anti-cycling Control modes Building Management System BMS CascadeService Notification Circulation pumpsOwner maintenance Maintenance Maintenance and annual startupService technician See the User’s Information Manual for instructionsMaintenance Check relief valve Inspect/replace hot surface ignitersInspect/replace hot surface igniter Inspect and clean burner Check all wiringCheck control settings Perform start-up and checks2Adjusting air shutter 399,999 750,000 Btu/ hr Models Adjusting combustion air pressure Checking manifold gas pressureValve Fitting Control Knob Inspect and clean the heat exchanger Review with ownerOiled bearing circulators Check control module fuses TroubleshootingBefore troubleshooting Check the followingOperation No DisplayNo Burner Unit DoesChecking temperature sensors Resistance TemperatureTemperature Resistance Operation Boiler Pump System Pump NoisyNo Pump DHW PumpFlow Switch Flame SequenceAnti-cycling HSI Current Low ErrorNo Flame Ign Flame CKTRunning Auto ResetNo Flame High LimitSensor Open Manual ResetInlet Low Sensor ShortedAPS Open Louver ProvingTank Open APS ClosedTemp O/Shoot Rem Ctrl FltParameters Progr No Error Stored Service BlkWatch Dog Error Low Voltage
Related manuals
Manual 44 pages 7.23 Kb Manual 80 pages 43.41 Kb Manual 44 pages 8.33 Kb

402 - 2072 specifications

The Lochinvar 402 - 2072 is a versatile and highly efficient boiler designed to meet the heating demands of modern residential and commercial applications. This model stands out due to its innovative technologies, advanced features, and a high level of reliability, making it an ideal choice for consumers looking for an enduring and economical heating solution.

One of the primary characteristics of the Lochinvar 402 - 2072 is its impressive energy efficiency. With an exceptional annual fuel utilization efficiency (AFUE) rating, this boiler ensures minimal energy waste, allowing homeowners and business operators to save significantly on their energy bills. The model incorporates advanced condensing technology that enables it to extract heat from the combustion gases, maximizing heat transfer and reducing emissions.

The Lochinvar 402 - 2072 is built with a robust stainless steel construction that enhances durability and resilience against corrosion and other environmental factors. This material not only prolongs the lifespan of the unit but also contributes to its outstanding thermal efficiency. Additionally, the boiler's compact design allows for flexible installation options, making it suitable for various spaces, including tight utility rooms and basements.

Equipped with a user-friendly control interface, the Lochinvar 402 - 2072 allows for easy monitoring and adjustment of settings. Its advanced digital display provides real-time data on system performance, ensuring the operator can maintain optimal performance and efficiency.

Another noteworthy feature is the unit's quiet operation. The design includes sound-dampening insulation and high-efficiency circulators, keeping noise to a minimum, which is an essential trait for both residential and commercial settings.

The Lochinvar 402 - 2072 is also designed with safety in mind. It incorporates multiple safety features including an automated vent damper, low water cutoff, and a comprehensive control system that monitors various operating conditions. This proactive approach to safety ensures that potential issues are identified and addressed before they become critical.

In conclusion, the Lochinvar 402 - 2072 boiler presents an exceptional combination of efficiency, durability, and user-friendly features. Its advanced condensing technology, stainless steel construction, and focus on safety make it a leading choice in the competitive boiler market, catering to the heating needs of a diverse range of applications while ensuring environmental responsibility. For those in search of a dependable and efficient heating solution, the Lochinvar 402 - 2072 is certainly worth considering.
Top Page Image Contents